Electrothermal MC810B MKII Instruction Book Download Page 21

Page: 21 / 24

Page 21 of 24 M6493 Issue 10.3

10. CUSTOMER SUPPORT.

For help and support in using this product, please contact

Bibby Scientific

Limited

at the following address.

Bibby Scientific Limited.

Beacon Road,
Stone,
Staffordshire ST15 0SA,
Great Britain.

Tel: +44(0)1785 812121
Fax: +44(0)1785 810405

•

General enquiries :

[email protected]

•

Order enquiries :

[email protected]

•

Technical support :

electrothermalhelp@bibby-
scientific.com

•

www.electrothermal.com

For the America’s and Canada, contact:
Techne Incorporated,

3 Terri Lane,

Suite 10 Burlington, NJ 08016 USA.

Toll free:800-225-9243Tel: 609-589-2560
Fax: 609-589-2571
Email:

[email protected]

Http

www.techneusa.com

11. PARTS AND ACCESSORIES.

AZ9035

Fuse F8A. Qty 10. (230V~ AC Product).

AZ6747

Mains cord and moulded IEC plug and lead set (Schuko).

AZ6705

Temperature Probe 250

C Max.

AZ6706

Temperature Probe 400

C Max.

AZ6741

Temperature Probe 800

C Max.

Summary of Contents for MC810B MKII

























Search results

Summary of Contents for MC810B MKII

Reviews:

Related manuals for MC810B MKII

Brands by name

Popular brands

Electrothermal MC810B MKII, Instruction Book

Search results

Summary of Contents for MC810B MKII

Reviews:

Related manuals for MC810B MKII

Brands by name

Popular brands