Electromotive XDI200 Installation Manual & Users Manual Download Page 42 | Manualshive

Page: 42 / 99

background image

________________________________________________________________________
XDI200 Manual Version 0.1

- Page 42 -

©2017 Electromotive, Inc.

4.8 Driver on Coil Logic Driven Coils

If you select Driver on Coil logic driven coils you will not use the shielded wires found on

pins [1,2,3,4 and 13,14,15,16].  Remove or tape these wires off.   The DOC logic level outputs are
very sensitive to miss wiring.  Be careful not to short these wires to ground or +12V.  Internal
damage will happen if you do.  The DOC logic outputs are +5 volt logic and cannot drive coils
directly.  It is allowed to connect up to two DOC coils to each logic output.

DOC coils either are 3 or 4 wire devices.

Connect To:

3 wire DOC

4 wire DOC

Power +12 V

DFU Power +12V
Switched

+12V

+12V

Signal

Pin 5, 6, 7, 10, 11 or 12

Signal

Signal

Power Ground

Engine Block Ground

Ground

Power Ground

Reference Ground

Pin 17 or 18 Black/White Not Present

Reference Ground

The wiring of the logic signals simply follows the plug wiring as noted in the standard DFU

wiring above. Where a coil spark plug wire connection is indicated substitute the DOC logic
output for that cylinders DOC coil. One DOC logic output is wired to two DOC coils.

SIGNAL CONNECTION EXAMPLES: VERIFY THE FIRING ORDER

4 Cylinder 6 Cylinder and Dual

Plug

8 Cylinder

Firing Order: 1-3-4-2

1-6-2-4-3-5

1-8-4-3-6-5-7-2

Standard
Coil

DOC Pin / Wire
Color to signal pin

Connect
to Coils

Connect to Coils

Connect to Coils

A1

5 Black/Gray

1 and 4

1 and 4

1 and 6

B1

6 Black/Red

2 and 3

3 and 6

4 and 7

C1

7 Black/Green

Not Used

2 and 5

Not Used

A2

10 Black/Blue

Not Used

1 and 4 (dual plug)

5 and 8

B2

11 Black/Pink

Not Used

3 and 6 (dual plug)

2 and 3

C2

12 Black/Orange

Not Used

2 and 5 (dual plug)

Not Used

When using the DOC logic outputs, tape up or remove the unused standard coil outputs.

WARNING: Before starting the engine when DOC coils are used, change the engine

configuration setting to DOC coil and set a fixed dwell time. If you do not know the exact dwell
time to use for the coil you have, start with 1.8 mSec. Failure to make this calibration change
may cause extreme damage to the coils.

«
...
40
41
42
43
44
...
»

Summary of Contents for XDI200




































































































Reviews:

No comments

Related manuals for XDI200

Brand: omnicharge Pages: 12

Brand: omnicharge Pages: 72

Brand: Makita Pages: 12

Brand: NEC Pages: 5

Brand: Hama Pages: 22

Brand: Camcar Pages: 6

Brand: WÄRTSILÄ Pages: 64

Brand: Paso Pages: 29

XMODS Custom RC

Brand: Radio Shack Pages: 4

Brand: Farad Pages: 8

Brand: METRON Pages: 4

Brand: Westcott Pages: 1

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: Minwax Pages: 7

TOURNEY REAR DRIVE SYSTEM - TECHNICAL

Brand: Shimano Pages: 2

SafeAir M-300 Pro

Brand: ParaZero Pages: 24

Temposonics TempoLink Smart Assistant

Brand: MTS Sensors Pages: 12

Brand: Mitsubishi Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands