Electromotive XDI200 Installation Manual & Users Manual Download Page 92 | Manualshive

Page: 92 / 99

background image

________________________________________________________________________
XDI200 Manual Version 0.1

- Page 92 -

©2017 Electromotive, Inc.

4. The main values from your old *.bin file should be transferred directly. However, for safety,

ALWAYS make sure that the old *.bin values are the same as the new values.

5. Save the bin file in the new WinTec software version (give it a new name).
6. Download the new file into your

XDI200

ECU as you normally would.

Following this step-by-step procedure should keep everything straightforward during the

upgrade process.

16.1.4

Firmware Upgrade Procedure

Care must be taken when installing different firmware versions on your

XDI200

ECU. Follow

the steps outlined below:

1.  Download the Firmware upgrade from the Electromotive website.
2.  Install the firmware upgrade on the PC that you will use to tune the engine.
3.  Connect the

XDI200

to the PC

’s serial or USB port and power it ON.

4. Startup the WinTec software, it should show in the System console that the unit was found

and display the firmware version.

5.  Turn-OFF power to the TEC unit.
6.  Turn on power to TEC but do not run engine
7.  Go to Tools > Options > Firmware Upgrade. Find and select the new .em3 file and

download

8. Once the upgrade is complete, cycle the power to the TEC. If the firmware upgrade was

successful, both LED’s will go GREEN. If the firmware upgrade failed, the ECCL LED will
stay RED and the crank will stay off. If this occurs, start the procedure over at step 5.

9. The firmware is now upgraded, you can begin/continue tuning.

«
...
90
91
92
93
94
...
»

Summary of Contents for XDI200




































































































Reviews:

No comments

Related manuals for XDI200

Brand: ABB Pages: 27

Brand: Eaton Pages: 21

Brand: AC Schnitzer Pages: 16

Brand: Makita Pages: 20

Brand: Panasonic Pages: 252

Brand: Hama Pages: 2

Brand: KDS Pages: 72

Brand: LAUMAS Pages: 44

Brand: Xerox Pages: 16

Brand: Öhlins Pages: 10

Brand: +GF+ Pages: 36

Brand: Hussmann Pages: 10

Brand: Desa Pages: 4

Brand: Raw Thrills Pages: 49

Brand: IFM Electronic Pages: 21

Brand: Acebil Pages: 11

Brand: Oliver Bonas Pages: 2

VXI/VMEpc 600 series

Brand: National Instruments Pages: 61

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands