4
Accessories
1*/**
Telescopic tube
2*
Extension
tubes
3**
Hose hose
4**
Carpet/hard
floor
nozzle
5**
Crevice
nozzle
6
Upholstery
nozzle
7
Dust
bag,
s-bag™
8*
Turbo
nozzle
9*/**
Parquet nozzle
10*
Easy clean kit
Safety precautions
Ergospace should only be used by
adults and only for normal vacuuming
in a domestic environment. The vacuum
cleaner features double insulation and
does not need to be earthed.
Never vacuum:
•
In wet areas.
•
Close to flammable gases etc.
•
Without a dust bag s-bag™ to avoid
damaging the cleaner. A safety device
is fitted, which prevents the cover
closing without a s-bag™. Do not
attempt to force the cover shut.
•
When housing shows visible signs of
damage
Never vacuum:
• Sharp
objects.
•
Fluids (this can cause serious damage
to the machine).
•
Hot or cold cinders, lit cigarette butts,
etc.
•
Fine dust, for example from plaster,
concrete, flour, hot or cold ashes.
The above may cause serious damage to
the motor – damage which is not covered
by the warranty.
Electrical cable precautions:
•
A damaged cable should only be
replaced by an authorised Electrolux
service centre.
•
Damage to the machine’s cable is not
covered by the warranty.
• Never pull or lift the vacuum cleaner
by the cable.
•
Disconnect the plug from the mains
before cleaning or maintenance of the
vacuum cleaner.
•
Regularly check that the cable is not
damaged. Never use the vacuum
cleaner if the cable is damaged.
All servicing and repairs must be carried out
by an authorised Electrolux service centre.
Be sure to keep the vacuum cleaner in a dry
place.
Before starting
11
Open the front cover on the machine
and check that the dust bag,
s-bag™, and the motor-/microfilter**
are in place. (See also Replacement
of filter(s))
12*
Open the back lid* on the machine
and check that the exhaust filter* is
in place.
13
Insert the hose until the catches
click to engage (press the catches to
release the hose).
3*
Insert the hose into the hose handle
until the catches click to engage
(press the catches to release the
hose).
14
Attach the extension tubes* or tel-
escopic tube* to the hose handle
and nozzle by pushing and twisting
together. (Twist and pull apart to dis-
mantle.)
15
Extend the electric cable and connect
it to the mains. The vacuum cleaner
is fitted with a cable winder. Once the
electric cable has been extended, it
stays in that position.
16
To rewind the cable, give it a slight
sharp pull and then release. The
cable will then automatically rewind.
17**
Adjust suction power by using the
suction control on the hose handle
17**
Models with ON/OFF control: Twist
the control once to the left to start
the vacuum cleaner. Twist the control
once more to the left to turn it off.
17**
Models with Power Regulation: Twist
the power control to the right to start
the vacuum cleaner and increase
the suction power. Twist the power
control to the left to decrease suction
power, and further to the left to turn it
off.
18
Practical parking positions (and at
the same time a backsaving feature)
when you pause during cleaning or
when you carry and store the vacuum
cleaner.
19
You can also carry the vacuum clean-
er using the handle on top or on the
lower front edge of the machine.
20*
Keep the hose in place while storing
the vacuum cleaner by extending the
elastic bumper cord and placing it
across the hose.
Getting the best results
21 Accessories on board
Upholstery nozzle and crevice nozzle to
be found under foldable cover.
Use the nozzles as follows:
Carpets:
Use the carpet/hard floor nozzle
with the lever* in position (32). Reduce
suction power for small carpets.
Hard floors:
Use the carpet/hard floor
nozzle with the lever* in position (33).
Wooden floors:
Use the parquet nozzle*
(9).
Upholstered furniture:
Use the upholstery
nozzle (6). Curtains, lightweight fabrics,
etc.: Use the upholstery nozzle (6).
Reduce suction power if necessary.
Frames, bookshelves, etc.:
Use the Easy
clean kit* (10).
Crevices, corners, etc.:
Use the crevice
nozzle (5).
Using the turbo nozzle*
22
Adjust the suction power by opening
or closing the air vent.
Note: Do not use the turbo nozzle on skin
rugs, rugs with long fringes or a pile depth
exceeding 15 mm. To avoid damaging the
carpet, do not keep the nozzle stationary
whilst the brush is rotating. Do not pass the
nozzle across electric cables, and be sure to
switch off the vacuum cleaner immediately
after use.
Replacing the dust bag,
s-bag™
23
The dust bag, s-bag™ must be
replaced latest when the indicator
window is completely red. Read with
the nozzle lifted up.
24
Open the front cover and lift out the
insert holding the s-bag™.
25
Pull the cardboard to remove the
s-bag™ from the insert. This automat-
ically seals the s-bag™ and prevents
dust leaking out.
26
Insert a new s-bag™ by pushing the
cardboard right into the end of the
groove in the insert.
27
Put the insert back into the bag
compartment, and close the cover.
Note. Replace the s-bag™ even if it is not
full (it could be obstructed). Also replace after
vacuuming carpet-cleaning powder. Be sure
to use only an original Electrolux dust bags,
s-bag™ Classic, s-bag™ Clinic, s-bag™ long
performance or s-bag™ Anti-odour.
Replacement of the filter(s)
Should be done with every 5th replacement of
the dust bag, s-bag™ Never use the vacuum
cleaner without filter(s).
A
Model without exhaust filter has to
be equipped with a combination-filter
(micro- motor-filter, Ref. No.
EF 74).
24
Open the front cover and lift out the
insert holding the s-bag™.
28
Pull the filter(s) holder upwards
until coming away from the groove.
Carefully pull the old, dirty filter(s) out
of the filter holder and replace with a
new filter(s).
29
Reattach the filter holder containing
the new filter(s).
27
Replace the insert holding the
s-bag™ and then close the cover.
B
Model with exhaust filter Follow steps
24, 28 and replace old motor-filter
English
