Electrolux MAGISTAR OVEN 6-10-20GN, Service Manual, Page: 83 / 124

83
Anomaly Type of
anomaly Description Possible
causes Instructions to User Action for Service*
N°243
BEtc Warning Error, excessive
time on closing
operation of the
vent valve
during cleaning
(VV1). Mechanical or
electrical prob-
lem with vent
valve. The oven has detected a
problem with cavity vent
operation. If cooking:
check the cooking result,
try to reset the message
also switching OFF/ON;
if message persists, call
Service and continue
cooking: clean the oven
only manually until fixing
the issue.
If cleaning: it is not possi-
ble to perform/complete
the cleaning cycle.
Switch OFF/ON to reset
the message. If the prob-
lem persists, call Service. Check cleanness of vent valve.
Check X35 and X46 on ACU (see
E.4
A.C.U Level T ,K, B, C
(Power Board) section.
Verify harness continuity and con-
nectors (see “Venting valve, VV1“
section in “Detailed appliance
and components description/
functioning“ chapter of the proper
Service manual).
Replace vent valve (see “Cavity
air valve“ section in “Servicing the
appliance“ chapter of the proper
Service manual).
Restart the oven to let the clean-
ing procedure to complete.
N°242
BEto Stops
cleaning. Error, excessive
time on opening
operation of the
vent valve
during cleaning
(VV1). Mechanical or
electrical prob-
lem with vent
valve. The oven has detected a
problem with cavity vent
operation. It is not possi-
ble to perform/complete
the cleaning cycle.
Switch OFF/ON for reset-
ting the error.
If the cleaning does not
restart, call Service. Check cleanness of vent valve.
Check X35 and X46 on ACU
(seeE.4
A.C.U Level T ,K, B, C
(Power Board) )
Verify harness continuity and con-
nectors (see “Venting valve, VV1
“ section in “Detailed appliance
and components description/
functioning“ chapter of the proper
Service manual).
Activate the vent valve from by-
pass environment to check func-
tionality D.3.2.2
By-Pass
environment
Replace vent valve (see “Cavity
air valve“ section in “Servicing the
appliance“ chapter of the proper
Service manual).
Restart the oven to let the clean-
ing procedure to complete.
N°224
BEtr Warning Boiler exces-
sive tempera-
ture raising time
(Tbol). - Broken heating
element.
- Broken Solid
State relay.
- Dirty burner. The oven has detected a
low performance in the
boiler. Please verify
cooking results. Verify boiler heating element;
Solid state relay; Burner clean-
ness; PWM malfunctioning/wrong
values.
N°241
Bhtc
Warning Warning on
excessive time
on closing oper-
ation of the vent
valve during
cooking (VV1).
- Flap (venting
valve) motor
reducer or micro
switch failure.
- Obstruction at
the venting
valve inlet.
It is possible to continue
using the oven; Cooking
results maybe different
from usual (probably
dryer than usual); With
the oven OFF and cold,
check if any obstruction
at the ventilation chimney
on the top of the oven. If
the warning persists, call
Service.
Check cleanness of vent valve.
Check X35 & X46 on ACU E.4
A.
C.U Level T ,K, B, C (Power
Board)
Verify harness continuity and con-
nectors (see “Venting valve, VV1“
section in “Detailed appliance
and components description/
functioning“ chapter of the proper
Service manual).
Activate the vent valve in Service
mode to check functionality.
Replace vent valve (see “Cavity
air valve“ section in “Servicing the
appliance“ chapter of the proper
Service manual).
Restart the oven to let the clean-
ing procedure to complete/heck
that the warning disappeared.