manualshive.com logo in svg

Electrolux MAGISTAR OVEN 6-10-20GN, Service Manual, Page: 42 / 124

Share
Download
Electrolux MAGISTAR OVEN 6-10-20GN Service Manual Download Page 42

42

PRIDE/Internet Explorer unzipping

Click on one of the files

Double click on the file

Now will appear a dialogue box for the download;

depending on the unzipping program you have installed on
your PC the view could change

Press SAVE AS

The downloaded zipped file must NOT be saved into your

USB key (DRIVE), it needs to be saved elsewhere and then
unzipped into your USB. In this illustration we have created on
our desktop a folder “digit programming file zip“.

D.3.3.4 Programming File upload (Software Upload)

The Programming file (that from now on we will call

P.F.

as

abbreviation) is the software application of the oven and this is
stored in the UI.
The

P.F.

will update the software edition refer to the UI App

version at chapter D.3.1.4

Oven Identity Card

.

The

P. F

installation will NOT erase the recipies of the customer nor change any personalization, parameters etc ; the software

update will update the application, not the parameters!!

WHEN TO UPDATE:

• When ever you see an older version UI application software chapter. The

P.F.

will update the software edition refer to the UI App

version at chapter D.3.1.4

Oven Identity Card

.

• In case of any spare part replacement (UI, ACU)

NOTE!
If a

P.F

has been updated it is mandatory to install also the latest parameter file

P.P.

2

3

4

Summary of Contents for MAGISTAR OVEN 6-10-20GN





























































































































Reviews:

No comments