manualshive.com logo in svg

Electrolux MAGISTAR OVEN 6-10-20GN, Service Manual, Page: 62 / 124

Share
Download
Electrolux MAGISTAR OVEN 6-10-20GN Service Manual Download Page 62

62

D.4.3

Software update B, C (Digit)

Refer also to D.2

Software Editions

for a complete list of the different editions of software available “in the market“.

IMPORTANT
The following instructions/illustrations are relative to software 1.3.2 onwards. Previous software editions could
differ to what is reported in this manual edition.

The software to update an oven is divided in two different packages:
•

Programming File (Software)

•

Programming Parameters (Parameters)

Each package can be installed individually but we

recommend to install both packages at the same time

.

All packages of software can be downloaded from the official TechDoc web pages (hereafter illustrations of the packages
appearance in PRIDE / AGELUX).

D.4.3.1 AGELUX Web site - Example illustration

•

Programming File

•

Programming Parameters

PNC 217882 touch oven / GAS

Summary of Contents for MAGISTAR OVEN 6-10-20GN





























































































































Reviews:

No comments