Electrolux EWM2000 Service Manual Download

Page: 41 / 74

ALARM CODES

SSD-P APdV, EB, HD 01/05

8.23

599 34 71-47

The sensing of the component (triac) that commands the Motor

device on the electronic board in not working properly.

Checks to do:

One of the Relays of the main board is not working properly.

Does not exist in the DC version.

Checks to do:

Change the main board and run again the

diagnostic cycle to verify any further possible

alarm

E53

E54

Change the main board and run again

the diagnostic cycle to verify any further

possible alarm

If there are burn marks on
electronic board, see page 13.1-2

Measure between all wires in the

connector J1 in main board and

the

body

of the

machine

(see page 9.1, point “3”).

Do you measure any dispersion?

see pic. 20

Unplug the connector in the motor and

measure between motor connectors and

body of the machine. Do you see any

dispersion? (-

see pic.21

Replace the Motor and run again the

diagnostic cycle to verify any further

alarm.

YES

Replace/change the cables /wiring and

run again the diagnostic cycle to verify

any further alarm.

Summary of Contents for EWM2000











































































Search results

Summary of Contents for EWM2000

Reviews:

Related manuals for EWM2000

Brands by name

Popular brands

Electrolux EWM2000, Service Manual

Search results

Summary of Contents for EWM2000

Reviews:

Related manuals for EWM2000

Brands by name

Popular brands