Electrolux EWM2000 Service Manual Download Page 31

Page: 31 / 74

ALARM CODES

SSD-P APdV, EB, HD 01/05

8.13

599 34 71-47

Is the door closed

properly?

YES

The machine is not able to lock the door.

(1st page)

Checks to do:

YES

Unplug the connectors on

door lock and measure as

follow:

- Measure between

connector 3 and 5, you

should NOT find an open

circuit.

- Instead between connector

4 and 5, you should find an
OPEN circuit (numbers are

printed on the component).

Is the door lock OK?

3 Connections

–

Traditional or instant door

lock device.

see pic. 17,18

To verify the cable measure the

following connections on main

board plugs:

-Measure between wire on J2-3
and J7, you should NOT find an

open circuit.

-Measure between wire on J2-1

and J2-3, you should find an

OPEN circuit.

-Measure between wire J2-1 and

wire going to connector 4 in the

door lock, you should find a short

circuit.

Is the system OK?

see pic. 13,16, 24

Change the door

lock and run the

diagnostic cycle

to measure any
further possible

alarm

Check/change the cables

and run again diagnostic

cycle to verify any further

possible alarm

Change the Door lock.

Is the machine working correctly?

Run again diagnostic cycle to

verify any further possible alarm

Verify mechanical coupling

between door lock and

door catch and eventually

change door catch/door

E41

Close the door correctly

and run the diagnostic cycle

to measure any further

possible alarm

Is the door

lock with 3

or 4

connectors?

4 Connections

(Instant door lock device)
-

see next page (8.14)

YES

Summary of Contents for EWM2000











































































Search results

Summary of Contents for EWM2000

Reviews:

Brands by name

Popular brands

Electrolux EWM2000, Service Manual

Search results

Summary of Contents for EWM2000

Reviews:

Brands by name

Popular brands