Electrolux EDS Installation Manual Download Page 28

Page: 28 / 40

Installation manual

A password is needed to continue.
The default password is set to 01234.
When the password is set you will enter the

INSTALLER MENU

Activate the

INSTALLER SERVICE

menu.

INSTALLER MENU

INSTALLER SERVICE

INITIAL SYSTEM SETUP

PROGRAM FORMULAS

DATA TRANSFER

SET UNITS OF MEASURE

Activate the

CLEAR DATA LOG

menu.

INSTALLER SERVICE

SERVICE PUMPS

VIEW SINK COUNT

VIEW SINK VOLUME

VIEW AMOUNT PUMPED

CLEAR DATA LOG

Before resetting the data log there will be a warning message on the display. Press Enter. Set the current date and
press Enter to reset the data log.

Note!

Resetting the data log will not affect the main program settings.

3.9 Electrolux wash program allocation

Enter the

MAIN MENU

and activate the

INSTALLER MENU

MAIN MENU

EMERGENCY PUMP STOP

USER PRIME PUMPS

USER MANUAL FLUSH

MANAGER REPORTS

INSTALLER MENU

VIEW EFFICIENCY

A password is needed to continue.
The default password is set to 01234.
When the password is set you will enter the

INSTALLER MENU

Activate the

PROGRAM FORMULAS

menu.

INSTALLER MENU

INSTALLER SERVICE

INITIAL SYSTEM SETUP

PROGRAM FORMULAS

DATA TRANSFER

SET UNITS OF MEASURE

Summary of Contents for EDS









































Search results

Summary of Contents for EDS

Reviews:

Related manuals for EDS

Brands by name

Popular brands

Electrolux EDS, Installation Manual

Search results

Summary of Contents for EDS

Reviews:

Related manuals for EDS

Brands by name

Popular brands