manualshive.com logo in svg

Electrolux EDS, Installation Manual, Page: 27 / 40

Share
Download
Electrolux EDS Installation Manual Download Page 27

Installation manual

27

Use the keypad and write a file name for the file.
Before downloading there will be a warning message on the display. Press Enter to download the selected setup file
to the USB stick.
The USB stick can now be used to upload the wash program to multiple machines.

3.8 Download reports to a USB stick

Enter the

MAIN MENU

and activate the

INSTALLER MENU

.

MAIN MENU

EMERGENCY PUMP STOP

USER PRIME PUMPS

USER MANUAL FLUSH

MANAGER REPORTS

INSTALLER MENU

VIEW EFFICIENCY

A password is needed to continue.
The default password is set to 01234.
When the password is set you will enter the

INSTALLER MENU

.

Activate the

DATA TRANSFER

menu.

INSTALLER MENU

INSTALLER SERVICE

INITIAL SYSTEM SETUP

PROGRAM FORMULAS

DATA TRANSFER

SET UNITS OF MEASURE

Insert the USB stick in the EDS controller.
Activate the

WRITE REPORTS

menu.

DATA TRANSFER

WRITE REPORTS

READ SETUP

WRITE SETUP

UPDATE FIRMWARE

WRITE ACTIVITY LOG

Set the current date for the report and press Enter.
Use the keypad and write a name for the report and press Enter to save to the USB stick.

Reset the data log

Enter the

MAIN MENU

and activate the

INSTALLER MENU

.

MAIN MENU

EMERGENCY PUMP STOP

USER PRIME PUMPS

USER MANUAL FLUSH

MANAGER REPORTS

INSTALLER MENU

VIEW EFFICIENCY

Summary of Contents for EDS









































Reviews:

No comments