ElectroFlip iConserve User Manual Download

Page: 1 / 16

background image

iConserve User Guide___________________________________________________

1

iConserve

User Guide

All information and instructions included in this manual are current as of March 22, 2014.

However, due to the fluid nature of advancing technology, some characteristics may change or

need modifications in the future. Should you encounter any problems or have any further

questions about your purchase, please visit us atpage.

WARNING!: Before attempting to install the transmitter and clamp sensor in your breaker
box or power source for your home or business FIRST consult with a local Certified
Electrician. In addition it’s highly recommended that you hire this Certified Electrician to
safely and properly install these components. Inappropriate contact with your breaker
box or main power source can be FATAL.

Table of Contents

Introduction………………………………………………………………………………………

2

Features………………………………………………………………………………………….

2

Overview………………………………………………………………………………………….

2

Display unit…………………………………………………………………………………...

2

Transmitter and sensor……………………………………………………………………..

2

Display information………………………………………………………………………….

3

Installation………………………………………………………………………………………..

3

Find power cable…………………………………………………………………………….

4

Replacing batteries………………………………………………………………………...

4

Link transmitter and display unit………………………………………………………….

4

Operating Guide……………………………………………………………………..................

4

Setting time and date……………………………………………………………………...

4

Advanced settings……………………………………………………………………...........

5

View instant and accumulative energy, cost, Co

2

……………………………………….

6

How to view historical data and charts…………………………………………………….

7

Switch alarm on or off…………………………………………………………………........

8

Must Read Warnings……..……………………….…………………………………………......

9

1
2
3
...
»

Summary of Contents for iConserve

















Reviews:

No comments

Related manuals for iConserve

AF-650 GP Series

Brand: GE Pages: 54

Brand: Panamax Pages: 2

Brand: Panamax Pages: 12

Brand: Panamax Pages: 40

Brand: Panamax Pages: 12

Brand: XINDAK Pages: 2

Brand: Pacific Power Source Pages: 463

NERTAMATIC 450 AC/DC

Brand: Air Liquide Pages: 20

Brand: Measurement Computing Pages: 33

Brand: ETA Systems Pages: 8

CONTRACTOR Series

Brand: Furman Pages: 14

Brand: ETA Systems Pages: 16

P-1800 PF Prestige Series

Brand: Furman Pages: 24

Brand: Phonic Pages: 8

Brand: Panamax Pages: 2

Brand: Panamax Pages: 4

Brand: California Instruments Pages: 246

Brand: Isotek Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands