ELECRAFT K3 Owner'S Manual Download Page 9

Page: 9 / 78

RECEIVER (Main and Sub)*

Sensitivity (MDS)

-136 dBm (typ.), preamp on, 500 Hz b/w. Reduced sensitivity near 8.2 MHz (first
I.F.).

6 m MDS with PR6 option:

-143 to -144 dBm (typ.).

KBPF3 option required for full general-cov erag e receive, including broadcast band
(0.5 to 1.7 MHz). Note: Sensitivity gradually decreas es below 1.8 MHz due to high-
pass response o f T-R switch. This protects the PIN diodes.

IMD3 Dynamic Range

> 100 dB typical at 5, 10, and 20 kHz spacing.

Blocking Dynamic Range

140 dB typical at 5, 10, and 20 kHz spacing

Image and I.F. Rejection

> 70 dB

Audio Output

2.5 W per channel into 4 ohms; typ. 10% THD @ 1 kHz, 2 W

S-Meter

Nom. S9 = 50 µV, preamp on; user-adjustable

Noise Blanker

Adjustable, multi-threshold/multi-width hardware blanker plus DSP blanker

Receive AF graphic EQ

+/- 16 dB/octave, 8 bands

Filter Controls

IF Shift/Width & Lo/High Cut with automatic crystal filter selection

Dynamic range measurements based on 400-Hz, 8-pole filter. Other av ailable filters have very similar perfo rmance; see

www.elecraft.com for full list.

Receive specifications are guaranteed only within ham bands.

TRANSMITTER *

Output Power

K3/100: 0.1 W

–

100 W typ. (reduced power in AM mode).

K3/10 (or K3/100 with PA bypassed): 0.1 W

–

12 W, HF-10 m; 8 W max on 6 m.

XVTR OUT (KXV3 option): 0.1 to 1.5 mW (-10 to +1.8 dBm).

Duty Cycle

CW and SSB modes, 100% 10-min. 100W key-down at 25 C ambient

True RF Speech Processor

Adjustable compression

Transmit AF graphic EQ

+/- 16 dB/octave, 8 bands

SSB TX Bandwidth

4 kHz max (> 2.8 kHz requires 6 kHz AM filter)

SSB TX Monitor

Post-DSP filtering/processing

VOX

DSP-controlled, adjustable threshold, delay, and anti-VOX

Full and Semi CW Break-In

Adjustable delay; diode T/R Switching

SSB Carrier Suppression

> 50 dB

Harmonic and Spurious
Outputs

> 50 dB below carrier @ 100W (> 60 dB on 6 meters)

CW Offset/Sidetone

300-800 Hz, adjustable (filter center frequen cy tracks sidetone pitch)

Mic

Front panel 8 pin mic connector; rear panel 3.5 mm mic connector. Switchable DC
bias voltage available fo r elect ret mics (see

MAIN:MIC SEL

menu entry)

* Transmit spe cifications are guarantee d only within ham bands.

Summary of Contents for K3














































































Search results

Summary of Contents for K3

Reviews:

Related manuals for K3

Brands by name

Popular brands

ELECRAFT K3, Owner'S Manual

Search results

Summary of Contents for K3

Reviews:

Related manuals for K3

Brands by name

Popular brands