ELECRAFT K3 Owner'S Manual Download Page 41

Page: 41 / 78

KANT3

Ant. Input Module

Main RX

Ant 1

KRX3

RX Ant.

KXV3

Sub RX

SA4

Includes C.O.R.

Aux RF

SA1

SA3

Figure 2. Main/Sub Re ceive r Routing with KXV3 Installe d

K3 with KAT3 ATU

The KAT3 internal AT U, which replaces the KANT3 antenna input module, provides a second SO239 antenna
jack (ANT 2). As shown in Figure 3, relay K3 routes either ANT 1 or ANT 2 to the main RF path. T he antenna

not

routed to the main path (the

non-transm it

enna)

opt

onal

ecei

ver

’

AUX

antenna. This requires that the two antennas connected to the KAT3 be well isolated from each other. If not, the

ecei

ver

’

car

-operated relay may turn on during transmit. If this occurs, you must either move the two

antennas farther apart, or not connect the sub receiver to the KAT3.

It may be preferable to connec

ecei

ver

’

auxi

input to the AUX RF connector on the rear panel.

A well-isolated receiving antenna can then be used with the sub receiver when required. (See

CONFIG:KRX3

for sub receiver antenna setup.)

Ant 1

Ant 2

KRX3

L-Network

KAT3 ATU

Sub RX

SA1

SA2

SA4

Includes C.O.R.

Aux RF

Main RX

Figure 3. Main/Sub Re ceive r Routing with KAT3 Installe d

Summary of Contents for K3














































































Search results

Summary of Contents for K3

Reviews:

Related manuals for K3

Brands by name

Popular brands

ELECRAFT K3, Owner'S Manual

Search results

Summary of Contents for K3

Reviews:

Related manuals for K3

Brands by name

Popular brands