background image

WARNING! 

Read carefully these instructions before installation and use!

SAFETY, MAIN REQUIREMENTS 

Before proceeding with the installation and commissioning of the water heater, it is essential to read the full text of this
booklet. It is  intended  to familiarize you with the water heater, the rules for proper and safe use, with the minimum
necessary maintenance and servicing activities. In addition, you will need to provide this booklet to be used by authorized
persons who will install and possibly repair the appliance in the event of a breakdown. The installation of the water heater
and the verification of its functionality are not a warranty obligation of the seller and / or the manufacturer.

Keep this booklet in a proper place for future use. Compliance with the rules described therein is part of the safe use of
the appliance and is part of the warranty conditions

ATTENTION!

  The installation of the water heater and its connection to the plumbing system shall

only be  performed  by qualified persons in accordance with the instructions in this booklet and the
current   local   regulations.  The   installation   of   the   safety   and   other   components   provided   by   the
manufacturer or recommended by him is MANDATORY!

ATTENTION!

  The   connection   of   the   water   heater   to   the   electrical   system   is   only   performed   by

qualified persons in accordance with the instructions in this booklet and the normative documents.
The appliance must be properly connected to both the current conductors and the protective loop! Do
not connect the appliance to the electrical system before filling the water tank with water! Failure to
comply with these requirements will cause the appliance to be dangerous, and it is forbidden to use
it!

ATTENTION!

  The two units of the appliance must be connected only by authorized persons. The

appliance must be properly connected and secured against refrigerant leakage into the atmosphere.

ATTENTION!

  The connection of the indoor unit with a built-in heat exchanger to the heat supply

system (solar and / or other water heating systems using water or an aqueous solution as a heat
carrier) is carried out by qualified and competent persons in accordance with the design provided by
them. The way of using such a water heater, that is heating the water in its water tank by the heat
carrier alternative of the electricity, as well as the observing of the safety measures, is carried out in
compliance with the rules and requirements described in the additional instructions for use, servicing
and maintenance. These additional instructions is provided by the company that has carried out the
design and assembly work on the connection of the water heater with the alternative heat sources

WARNING!

 When using the appliance there is a risk of burning with hot water!

WARNING!

 Do not touch the appliance and its control panel with wet hands, or if you are barefoot or

standing in a wet place!

WARNING!

  This   appliance   is   not   intended   for   use   by   persons   (including   children)   with   limited

physical, sensory or mental capabilities or with insufficient experience and knowledge unless they are
supervised or instructed by a person responsible for their safety! Children should be monitored in
order not to play with the appliance!

ENVIRONMENT PROTECTION

This appliance is marked in accordance with the Directive  for waste from electrical ot electronic
equipment (WEEE). When you take care that, after exhausting  its  work  capacity, this appliance is
disposed in the right way, you will help prevent possible negative consequences for the environment
and human health

The symbol 

 on the appliance or on the documents attached to the appliance indicates that this

appliance should not be treated as household waste. Instead, it must be handed over to a specialized
recycling point for electrical and electronic equipment. Dispose of in accordance with local waste
disposal regulations. For more detailed information on the treatment, recovery and recycling of this

2

Summary of Contents for HPWH 120

































Reviews: