ELBRO ST-SK1 Installation Manual Download Page 16

31

30

RFID Tag 

Features

The RFID tag enables you to disarm your system or unlock electronic door locks.

Register in the control panel

Refer to the instructions in the table page 8 of this manual (“

RFID TAG

”). 

Specifications

Dimensions

45 x 30 x 7 mm

Troubleshooting and maintenance

FAQ 

Issue

Cause of malfunction

Solution

No response following 

interaction with the 

control panel

The control panel is switched off

Open the battery compartment and 

turn the power on

Electricity grid failure

Contact your electricity provider

Backup batteries are empty

Plug the AC adapter to an AC socket

Accessories cannot 

connect to the control 

panel

The control panel is not in 

Connection mode

Make sure the control panel is in 

Connexion mode

Accessories have not been 

triggered for connection

Make sure the accessory is triggered so 

to send a signal to the control panel

When attempting the 

connection, the control panel 

beeps twice

The accessory has already been 

connected

Make sure you do not trigger any 

other accessory when connecting one 

accessory to the control panel (e.g. do 

not stay in the detection scope of a 

motion detector if it is not the one you 

want to connect)

No response from the 

control panel following 

commands from the 

remote control

The remote control has not been 

connected to the control panel

Follow the instructions in this manual 

to connect the remote control to the 

panel

Remote control is too far from 

the control panel

Transmission distance of the remote 

control: 80 m (in open area)

A signal repeater can be installed to 

increase the transmission distance

RFID tag fails to disarm 

the system

RFID tag has not been connected 

to the control panel

Follow the instructions in this manual 

to connect the RFID tag to the control 

panel

Impossible to access 

settings from the control 

panel

You are not in the setup menu of 

the LCD display

Enter your admin code followed 

by “

Enter

“ to enter the setup 

menu

Summary of Contents for ST-SK1



















Reviews: