background image

EN

- 9 -

exceed the maximum charging times. These 

charging times apply only to discharged 

batteries. Frequent insertion of a charged 

or partly charged battery pack will result in 

over-charging and cell damage. Do not leave 

batteries in the charger for more than 48 

hours.

8. 

Never use or charge batteries if you 

suspect that the last time they were 

charged was more than 12 months 

previously. 

There is a high probability 

that the battery pack has already su

 ered 

dangerous damage (exhaustive discharge).

9.  Charging batteries at a temperature below 

50°F (10°C) will cause chemical damage to 

the cell and may cause a 

fi

 re.

10.  Do not use batteries which have heated 

during the charging process, as the battery 

cells may have su

 ered dangerous damage.

11.  Do not use batteries which have su

 ered 

curvature or deformation during the charging 

process or which show other non-typical 

symptoms (gassing, hissing, cracking,…)

12.  Never fully discharge the battery pack 

(recommended depth of discharge max. 

80%) A complete discharge of the battery 

pack will lead to premature ageing of the 

battery cells.

13.  Never charge the batteries unsupervised.

Protection from environmental in

fl

 uences

1.  Wear suitable work clothes. Wear safety 

goggles.

2. 

Protect your cordless tool and the battery 

charger from moisture and rain. 

Moisture 

and rain can cause dangerous cell damage.

3.  Do not use the cordless tool or the battery 

charger near vapors and in

fl

 ammable liquids.

4.  Use the battery charger and cordless tools 

only in dry conditions and an ambient 

temperature of 50°F to 104°F (10°C to 40°C).

5.  Do not keep the battery charger in places 

where the temperature is liable to reach over 

104°F (40°C). In particular, do not leave the 

battery charger in a car that is parked in the 

sunshine.

6. 

Protect batteries from overheating. 

Overloads, over-charging and exposure to 

direct sunlight will result in overheating and 

cell damage. Never charge or work with 

batteries which have been overheated – 

replace them immediately if possible.

7. 

Storage of batteries, battery chargers 

and cordless tools. 

Store the charger and 

your cordless tool only in dry places with an 

ambient temperature of 50°F to 104°F (10°C 

to 40°C). Store the Lithium-Ion rechargeable 

battery in a cool and dry place at 50°F to 68°F 

(10°C to 20°C). Protect them from humidity 

and direct sunlight! Place only fully charged 

batteries in storage (charged at least 40%).

8.  Prevent the Lithium-Ion battery pack from 

freezing. Battery packs which were stored 

below 32°F (0°C) for more than 60 minutes 

must be disposed of.

9.  When handling batteries beware of 

electrostatic charge: Electrostatic discharges 

cause damage of the electronic protection 

system and the battery cells. Avoid 

electrostatic charging and never touch the 

battery poles.

Battery C Disposal

Disposal

Should your appliance need replacement after 

extended use, do not dispose of it with the 

household refuse, but in an environmentally safe 

way.

Waste produced by electrical machine 

items should not be handled like normal 

household rubbish. Please recycle where 

recycle facilities exist. Check with your local 

authority or retailer for recycling advice.

Always dispose of your battery pack according 

to federal, state, provincial and local regulations. 

Contact a recycling agency in your area for recycling 

locations.

 CAUTION

! Even discharged battery packs 

contain some energy. Before disposing, use 

electrical tape to cover the terminals to prevent 

the battery pack from shorting, which could cause 

fi

 re or explosion.

 WARNING!

 To reduce the risk of injury or 

explosion, never burn or incinerate a battery 

pack even if it is damaged, dead, or completely 

discharged. When burned, toxic fumes and 

materials are emitted into the surrounding 

atmosphere.

1.   Batteries vary according to device. Consult 

your manual for speci

fi

 c information.

2.   Install only new batteries of the same type in 

your product (where applicable).

3.   Failure to insert batteries in the correct 

polarity, as indicated in the battery 

compartment or manual, may shorten the life 

of the batteries or cause batteries to leak.

4.   Do not mix old and new batteries.

5.   Do not mix Alkaline, Standard (Carbon-Zinc), 

 

Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb   9

Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb   9

21.04.2022   12:54:40

21.04.2022   12:54:40

Summary of Contents for 4020455















































Reviews: