EN
- 6 -
DANGER!
When using the equipment, a number of safety
precautions must be observed to avoid injuries
and damage. Please read the complete operating
instructions and safety information with due care.
Keep these operating instructions in a safe place
so that the information is available at all times. If
you give the equipment to any other person, hand
over these operating instructions and the safety
information as well. We cannot accept any liability
for damage or accidents which arise due to
failure to follow these instructions and the safety
information.
1. Safety information
DANGER!
Read all the safety information and
instructions.
Failure to adhere to the safety
information and instructions set out below
may result in electric shock,
fi
re and/or serious
injury.
Keep all the safety information and
instructions in a safe place for future use.
General safety information for power tools
The term “power tool“ used in the safety
regulations refers to power tools operated from
the mains power supply (with a power cable) and
to battery operated power tools (without a power
cable).
1) Work area safety
a)
Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b)
Do not operate power tools in explosive
atmospheres, such as in the presence of
fl
ammable liquids, gases or dust.
Power
tools create sparks which may ignite the dust
or fumes.
c)
Keep children and bystanders away while
operating a power tool.
Distractions can
cause you to lose control.
2) Electrical safety
a)
Power tool plugs must match the outlet.
Never modify the plug in any way. Do
not use any adapter plugs with earthed
(grounded) power tools.
Unmodi
fi
ed plugs
and matching outlets will reduce risk of
electric shock.
b)
Avoid body contact with earthed or
grounded surfaces such as pipes,
radiators, ranges and refrigerators.
There
is an increased risk of electric shock if your
body is earthed or grounded.
c)
Do not expose power tools to rain or wet
conditions.
Water entering a power tool will
increase the risk of electric shock.
d)
Do not abuse the cord. Never use the
cord for carrying, pulling or unplugging
the power tool. Keep cord away from
heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the
risk of electric shock.
e)
When operating a power tool outdoors,
use an extension cord suitable for
outdoor use.
Use of a cord suitable for
outdoor use reduces the risk of electric
shock.
f)
If operating a power tool in a damp
location is unavoidable, use a ground
fault circuit interruptor (GFCI) protected
supply.
Use of an GFCI reduces the risk of
electric shock.
3) Personal safety
a)
Stay alert, watch what you are doing and
use common sense when operating a
power tool. Do not use a power tool while
you are tired or under the in
fl
uence of
drugs, alcohol or medication.
A moment of
inattention while operating power tools may
result in serious personal injury.
b)
Use personal protective equipment.
Always wear eye protection.
Protective
equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c)
Prevent unintentional starting. Ensure
the switch is in the O
ff
-position before
connecting to power source and/or
BATTERY pack, picking up or carrying the
tool.
Carrying power tools with your
fi
nger on
the switch or energizing power tools that have
the switch on invites accidents.
d)
Remove any adjusting key or wrench
before turning the power tool on.
A wrench
or a key left attached to a rotating part of the
power tool may result in personal injury.
e)
Do not overreach. Keep proper footing
and balance at all times.
This enables
better control of the power tool in unexpected
situations.
f)
Dress properly. Do not wear loose
clothing or jewellery. Keep your hair,
clothing and gloves away from moving
parts.
Loose clothes, jewelery or long hair
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 6
Anl_TE_AC_36_6_8_Li_OF_USA_SPK7.indb 6
21.04.2022 12:54:40
21.04.2022 12:54:40
