background image

 

www.ehs-heating.com 

 

EHS Electric Combi and System Boilers 

1.

 

Introduction 

The EHS Electric Boiler range will give years of trouble-free service and the following instructions will assist you in 

obtaining the best performance and most economical settings for your appliance. 

ATTENTION: Only qualified engineers and approved service engineers are recommended for installing and servicing 

this product. Unqualified personal and the use of nonstandard parts can be dangerous and will invalidate the 

manufacturer’s warranty. 

The installation must be performed in accordance with current IEE Wiring Regulations, Building Regulations, Water 

Fitting Regulations (England and Wales) or Water Bylaws (Scotland) and all relevant British standards. 

It is very important that you have read and fully understood this manual before installation of the EHS Electric 

Boilers to ensure their long life. This instruction manual should be kept in a place close to the appliance for easy 

reference. Please read the whole manual before attempting installation and follow these installation instructions 

and operating instruction to ensure long life of this EHS Boiler. These instructions must be conserved and given to 

any new user. 

All EHS Electric Boilers are guaranteed from manufacturing defects for a full 5 years. To ensure that you are eligible 

for this guarantee you must register the boiler at www.ehs-heating,com within the time specified in the warranty 

terms and conditions. This can be found at the back of this manual and on the EHS website. The warranty relates to 

any manufacturing defects and covers the replacement of any faulty parts. The guarantee does not cover any 

damage or faults that are a consequence of poor installation or faults caused by leaks within the boiler. It is 

therefore very important that all connections are thoroughly checked by the installer prior to leaving it with the 

customer. All work that takes place under the guarantee must be agreed with EHS prior to commencing the 

installation.  

This appliance must only be used and programmed by an authorised adult. It should not be used by children or 

anyone who has not read the installation manual. If in doubt, seek expert advice. 

 

 

2.

 

HEALTH AND SAFETY 

At EHS we take every precaution where possible to design and manufacture our products to meet the safety 

requirements, when installed and operated according to the correct procedures. All products are comprehensively 

examined and tested before despatch. 

Under the Consumer Protection Act 1974 it is a requirement to provide information on substances harmful or 

hazardous to health (COSHH Regulations 1988) 

Materials used in the manufacture of this appliance are non-hazardous and do not require any special precautions 

when fitting or servicing this appliance.  

It is the responsibility of the user or engineer to use the correct Personal Protective Equipment and Clothing when 

installing or working on this appliance.  

 

 

 

 

Summary of Contents for ALC1-1PCO12



































Reviews: