EHRET Voletronic io Installation And Operating Instructions Manual Download Page 2

2

Notes

the present installation and operating instruc-
tions describe the commissioning of the eHret 
Voletronic io window shutter drive with 
wireless remote control.

carefully read through these operating instruc-
tions prior to commissioning. observe the 
specified process steps and take into account 
the notes and recommendations given. Knowl-
edge of and technically impeccable implemen-
tation of the given safety notes and warnings 
are prerequisite for the safe and proper opera-
tion of the Voletronic io window shutter 
drive. insufficient knowledge at the time of 
commissioning and utilisation leads to the loss 
of any liability claims against eHret GmbH. 
any installation or operation in deviation from 
our installation and operating instructions – ei-
ther in full or in part – will result in the warranty 
becoming void.

installation of the shutters in accordance with 
the eHret window shutter installation instruc-
tions is a prerequisite for the commissioning of 
the eHret Voletronic io window shutter 
drive.

  

Remove the labels stuck to the shutters after 
installation!

these installation and operating instructions 
are addressed to qualified specialist personnel. 
Qualified specialist personnel are persons who 
are familiar with the transport, setup, installa-
tion, commissioning and operation of the prod-
uct and who have appropriate qualifications for 
their work. specialist personnel must know and 
observe the relevant standards and/or guide-
lines. 

these installation and operating instructions 
are a component part of the product and are 
therefore always to be retained until the prod-
uct is disposed of.

these installation and operating instructions 
are to be passed along in the event of the sale 
of this product. this product is in accordance 
with general rules of technology. safety-con-
scious behaviour is necessary for undertaking 
safe commissioning. For this reason, observe 
the following notes.

should you not understand something in these 
installation and operating instructions unam-
biguously, do not fail to contact the specialist 
personnel at eHret GmbH, 77972 Mahlberg 
(Germany).

Summary of Contents for Voletronic io









































Reviews: