Effort International RX3000 Manual Download Page 19 | Manualshive

Page: 19 / 23

background image

19

Chapter 4

Tuning

Step-by-step instructions for tuning the TX3000 board follow. For the receiver see
RX 3000 Tuning Guide.

4.1. One (1) Opto TX Output

The following instruments are recommended for tuning:

−

Battery powered oscilloscope (two channels, cursor readout function

recommended).

−

10: 1 oscilloscope probe.

−

Multimeter.

4.2. Preparation

• Power OFF the TX3000 board (remove PWR connector at socket X1).

• Ensure that the antenna is connected to the correct socket (X5) on the TX3000
board.

• Turn the amplitude potentiometer R76 (LVL to almost (7/8) full power clockwise).

• Check the default setting of jumper J15 to J14 (see following the table).

«
...
17
18
19
20
21
...
»

Summary of Contents for RX3000
























Reviews:

No comments

Related manuals for RX3000

Brand: Yaesu Pages: 120

Brand: Icom Pages: 73

Brand: Harman Kardon Pages: 8

Brand: Aiwa Pages: 20

AquaTronics MS-850

Brand: ASA Electronics Pages: 5

Brand: Icom Pages: 116

Brand: ZoneVu Pages: 33

SD 236BT/RDS/USB/AX

Brand: Majestic Pages: 6

Brand: O-Lynx Pages: 16

Brand: PCB Piezotronics Pages: 6

Brand: JRC Pages: 44

Brand: Thurlby Pages: 24

Brand: azur Pages: 98

Brand: Icom Pages: 7

Brand: Sennheiser Pages: 28

Digital Freeview Receiver

Brand: Tevion Pages: 2

PowerTalk Head w/ADSP & SNS 04-22

Brand: SGC Pages: 72

Brand: Omega Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands