88
Controlling the SD-90 via MIDI
Changing the MFX type (Native mode)
fig.8-04_99
To change the effect type of the enhanced sounds
selected for parts 1–3, transmit the following system
exclusive message.
Address (p1 p2)
:
when changing the insertion effect of part 1 = 11 00
when changing the insertion effect of part 2 = 11 20
when changing the insertion effect of part 3 = 11 40
:
Data (tt):
Effect type number
For details on effect types, refer to
(p. 105), and to “Multi-effect parameters”
(MFX_E.pdf) on the included CD-ROM. No effect is assigned to Effect Type number 00 (THROUGH).
Checksum (ss): For details on the calculation method, refer to the section “Calculating the checksum”
within “MIDI implementation” (MIDIImple_E.pdf) on the included CD-ROM.
*
This is valid if the MFX select of parts 1–3 has not been changed since a Native Reset message was received.
<Example> Specifying 14: STEREO CHORUS as the effect of an enhanced sound for part 2
fig.8-05_99
Transmit the following system exclusive data.
Using MFX with other parts (Native mode)
By transmitting the following system exclusive message, the insertion effect used by the enhanced sounds
selected for parts 1–3 can be used by other parts. The output of all parts that use that MFX will be mixed
and sent to the MFX.
• Do not change the MFX source of the three insertion effects after a Native Reset message is received.
• This will not work if effect type 00 (no effect: THROUGH) has been specified for the enhanced sounds
selected for parts 1–3.
• Any control performed on the MFX will apply equally to all parts that use that MFX.
fig.8-06_99
1.
Transmit “Output Select=MFX” to specify MFX as the
output of the part.
Address (pp)
:
when using the MFX for part 1 = 20
when using the MFX for part 2 = 21
:
when using the MFX for part 32 = 3F
Data:
00(output assign = MFX)
Checksum (ss
): For details on the calculation method, refer to “Calculating the checksum” in “MIDI
implementation” (MIDIImple_E.pdf) on the included CD-ROM.
F0 41 10 00 48 12 [p1 p2 06 00] [tt] [ss] F7
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
MFX Type
Number
Patch Common
MFX1
MFX Type
(1) Exclusive status
(2) ID (Roland : 41H)
(3) Device ID
(4) Model ID (SD-90 : 00H 48H)
(5) Command ID (Data set : 12H)
(6) Address
(7) Data
(8) Checksum
(9) End of Exclusive
F0 41 10 00 48 12 [11 20 06 00] [0E] [3B] F7
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
Multitimbre
Mode Part 1
MFX Type
Number
Patch Common
MFX1
MFX Type
F0 41 10 00 48 12 [10 00 pp 1F] [00] [ss] F7
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
00 (=MFX)
Part
Output
Assign
sd90_manual_e.book 88 ページ ２００４年１０月４日 月曜日 午後３時２８分
