manualshive.com logo in svg

ECKELMANN VS 3015 CT, Operating Instruction, Page: 74 / 219

Share
Download
ECKELMANN VS 3015 CT Operating Instruction Download Page 74

 

 

Firmware V1.41 V1

08.11.2022

74/219

•

•
•
•

•

•

•
•

•

and unloaded sequentially but according to the operating time. If a fan must be loaded, the fan with the 
shortest operating time is switched on. If a fan must be unloaded, the fan with the longest operating time is 
switched off. Furthermore, base load rotation of the fans is performed in this operating mode. If the tG 
controller is in the neutral zone for a configurable time 

Cycle time F.

 (menu 3-7), after expiry of this time, if 

available the fan with the shortest time will be loaded and the fan with the longest time unloaded for this.

2. 

Cycle time F.

A time can be entered following which, depending on the previously described operating modes, either fan 
switching or base load rotation will be performed.

5.6.12  Kickstart

This function monitors long standstill times of individual fans. In the event of exceeding a configurable standstill 
time, this fan will be switched on for a short time. This function is intended to prevent the seizure of individual 
fans in cold seasons.

Function scope

Support of all control modes of the condenser controller (step, speed, parallel combined and stages 
combined)
The kickstart last for 5 seconds for all control modes
A minimum wait time of 5 minutes between one kickstart and the next is implemented
The kickstart is only performed for fault-free (motor cut-out) and enabled fans (System Configuration menu 
3-1)
Control modes with an FC are executed at minimum speed (parameter "

Min. speed

", menu 3-2-2-1) during 

the kick-start
For the parallel combined control mode, the FC enable (Vent DigOut 1) is also actuated if this is OFF

Parametrisation

Parameter

Menu

Value range

Default

Unit

Description

Fan Kickstart

3-2-2-1

YES / NO

NO

-

The function is activated with YES

Fan Offtime

3-2-2-1

24..240

24

hours

Standstill time of a fan, after which the 
kickstart is performed (only visible if 
parameter 

Fan Kickstart

 is set to YES)

Fan Kicklimit

3-2-2-1

0..20

5

Kelvin

tc-Setpoint / tc-Actual difference, from 
which the function will be active. For 
example for tc-Setpoint = 20 °C, 

Fan 

Kicklimit

 = 5 K. Function would be active 

starting from a tc-Actual greater than 15 
°C.

(only visible if parameter 

Fan Kickstart

 is 

set to YES)

Restrictions

The function is inactive for measuring circuit errors of the tc actual value

 

The function is inactive when "Fan off w/comp" (menu 3-2-2-1) is set to YES and all compressors are 
switched off
The function is inactive when Service mode (menu 8) is active

5.7  Medium Pressure Regulation

The controller regulates the medium pressure (MP) of a CO

2

 system using a PI controller. The required 

correcting variable for the regulation is provided via the analogue output 4 (terminals 63/64, 0..10 volts).

Summary of Contents for VS 3015 CT




























































































































































































































Reviews:

No comments