Echo CS-670 Operator'S Manual Download Page 8 | Manualshive

Page: 8 / 26

Echo CS-670 Operator'S Manual Download Page 8

8

CS-670

PREPARATION FOR USE

CAUTION

• All adjustment, should be made cold.
• Always wear gloves when working on chain.

MOUNTING GUIDE BAR AND
CHAIN

• Install the spiked bumper on the front of

machine. (Use two bolts 5

×

12 mm)

KICK GUARD

®

TO BAR

INSTRUCTIONS

Tools Needed: Two 11 mm (7/16 in) Wrenches.

For saws with Kick Guard

®

P/N 28932 and

Symmetrical Low-Kick type (Double Guard)
guide bars.

1. Install bolt (A) in

front hole (B) of Kick Guard

®

and through front hole (C) in guide bar.

2. IMPORTANT: Dimple (D) in Kick Guard

®

must

engage recess (E) in guide bar.

3. Tighten nut (F) and bolt (A) using 11 mm (7/16 in)

wrenches until snug. Make certain Kick Guard

®

is flush against guide bar.

4. Tighten nut (F) 1/8 additional turn.

5. Check to make certain Kick Guard

®

is tight on

guide bar.

Bolt (A)

Dimple (D)

Recess (E)

Front hole (C)

Front hole (B)

Nut (F)

Guide bar

Kick Guard

®

Two bolts 5

×

12 mm

Spiked bumper

«
...
6
7
8
9
10
...
»

Summary of Contents for CS-670



























Reviews:

No comments