manualshive.com logo in svg

Echo CS-670, Operator'S Manual, Page: 18 / 26

Share
Download
Echo CS-670 Operator'S Manual Download Page 18

18

CS-670

MAINTENANCE AND CARE

CARBURETOR ADJUSTMENT

Every unit is run at the factory and the carburetor is
set in compliance with Emission Regulations. In
addition, the carburetor is equipped with “H”  (High
Speed Needle) and “L” (Low Speed Needle) needle
adjustment limited that prevent settings outside
acceptable limits.

1. Before adjusting carburetor clean or replace air

filter and muffler, “Spark Arrestor Screen”.

2. Make sure the cutting attachments such as bar

and chain are properly adjusted.

3. Start engine and run several minutes to bring to

operating temperature. Flash choke twice during
warm-up to clear any air from the fuel system.

4. Stop engine.

Turn “H” speed needle counterclockwise (CCW)
to stop.
Turn “L” speed needle midway between full
clockwise (CW) stop and CCW stop.

5. Idle Speed Adjustment:

• Start engine, turn “Idle” speed adjustment

screw CW until the saw chain begins to turn,
then turn screw out CCW until the saw chain
stops turning.
Turn screw out, CCW, an additional 1/4 turn.

6. Accelerate to full throttle for 2 - 3 seconds to

clear any excess fuel in the engine, then return
to idle.
Accelerate engine to full throttle to check for
smooth transition from idle to high speed.
If engine hesitates turn “L” needle CCW 1/8 turn
and repeat acceleration.
Continue adjustment until smooth acceleration
results.

7. Check idle speed and reset if necessary as

described in item 5. If a tachometer is available
idle speed should be set as specified in the
Instruction Manual.

WARNING   

   DANGER

CUTTING ATTACHMENT MUST NOT TURN
OR MOVE WHEN UNIT IS IDLING.

CAUTION

When starting, idling adjustment speed should
be adjusted not to rotate the saw chain.
Correct idle speed is adjusted 2,900 to 3,100
r/min.
Or 1/4 turn CCW from the point the chain stops
moving.
When there is some trouble with the carburetor,
refer to your dealer.

Idle adjusting screw (T)

High speed needle (H)

Low speed needle (L)

Summary of Contents for CS-670



























Reviews:

No comments