manualshive.com logo in svg

Echo CS-670, Operator'S Manual, Page: 23 / 26

Share
Download
Echo CS-670 Operator'S Manual Download Page 23

23

CS-670

SAW CHAIN

CAUTION

Do not use replacement saw chain unless it has
been designated as meeting the CSA Z 62.3
kickback performance requirements.

NOTE

LOW KICKBACK SAW CHAIN is the chain
which has met the kickback performance
requirements of CSA Z 62.3 (safety
requirements for gasoline-powered chain saws).

CHAIN AND GUIDE BAR COMBINATION

  

The following combinations are recommended to the model CS-670.

Side plate angle

Top plate filing angle

25°

60°

Parallel

0.64 mm

↓↓↓↓↓

↑↑↑↑↑ ↑↑↑↑↑

↓↓↓↓↓

GUIDE BAR

Replacement guide bars.

The following guide bars may be considered to
have equivalent kickback energy.

• Sprocket nose guide bars of the same length

and nose radius, same pitch and having the
same number of teeth.

• A hard nose guide bars of the same length and

nose radius as a sprocket nose bar.

Properly filed cutters are shown as illustration.

When setting of the chain is finished, soak it in oil
and wash away filings completely before using.

- When chain has been filed on the bar, supply

sufficient oil to it, rotate the chain slowly to wash
away the filings before using again.

- If the chain saw is operated with filings clogged

in the groove, the saw chain and the guide bar
will be damaged prematurely.

- If the saw chain becomes soiled with resin, for

instance, clean it with kerosene and soak in it oil.

NOTE

These angles are referred to as Oregon 72LG,
72L. To sharpen other follow chain
manufacturer’s instruction.

Top plate cutting angle

Depth gauge

@ Standard configuration

60°

406 (16)

161386001

160386001

9.53 (3/8)

72LG, 72L

60

508 (20)

201387001

200387001

9.53 (3/8)

72LG, 72L

70

@

610 (24)

241388101

240388101

9.53 (3/8)

72LG, 72L

81

686 (27)

270389301

9.53 (3/8)

72LG, 72L

93

Guide Bar

Saw chain

Length

ECHO Part No.

Pitch

Type

Links

mm (in)

Double Guard

Symmetrical

mm (in)

OREGON

Summary of Contents for CS-670



























Reviews:

No comments