manualshive.com logo in svg

Echo CS-670, Operator'S Manual, Page: 20 / 26

Share
Download
Echo CS-670 Operator'S Manual Download Page 20

20

CS-670

Brake band

Adjuster

Direction
to tension

↓↓↓↓↓

↑↑↑↑↑

1 mm

Mark

Adjusting brake band

Adjuster

Brake band

Cover

FUEL FILTER

• Check periodically.

• Do not allow dust to enter fuel tank.

• Clogged filter will cause difficulty in starting

engine or abnormalities in engine performance.

• Pull the fuel filter out through fuel inlet port with a

piece of steel wire or the like.

• When the filter is dirty, replace it.

• When the inside of the fuel tank is dirty, rinsing

the tank out with gasoline can clean it.

OIL FILTER

• Check periodically.

• Do not allow dust to enter into oil tank.

• Clogged oil filter will affect the normal lubricating

system.

• Pull it out through oil filling hole with a piece of

steel wire or the like.

• If the filter is dirty, wash it in gasoline or replace

it.

• When the inside of the tank gets dirty, rinsing the

tank out with gasoline can clean it.

AUTOMATIC OILER

• The discharge volume of the automatic oiler is

adjusted to 8 mL/min approxmately at 7,000
r/min, prior to shipment from factory.

- To increase the delivery volume, turn the

adjusting knob clockwise.
When the knob touches stopper and stops,
this position indicates maximum discharge
volume. (15 mL/min at 7,000 r/min)

- Do not turn the adjusting knob beyond the

maximum or minimum limit of volume
adjustment.

ADJUSTING THE CHAIN BRAKE

When brake band is worn or elongated, adjust the
location of adjuster peak  as follows.

• Remove the clutch cover.

• Remove the cover and side plate.

• Turn adjuster position to set its peak to the

correct tensioning location.

• Ensure that clutch drum can be turned freely by

hand when brake handle is in cutting position
(release position).

CAUTION

ECHO recommends that an authorized ECHO
servicing dealer should service the chain brake.

Oil filter

Fuel filer

Oil cap

Fuel cap

Decrease

Increase

Adjusting knob

Summary of Contents for CS-670



























Reviews:

No comments