manualshive.com logo in svg

Echo CS-670, Operator'S Manual, Page: 4 / 26

Share
Download
Echo CS-670 Operator'S Manual Download Page 4

4

CS-670

   NOMENCLATURE OF PARTS

1

2

REPLACEMENT BAR AND CHAIN

PEMPLACEMENT DU GUIDE ET DE LA CHAÎNE

GUIDE BAR P/NO. CHAIN TYPE

CKA

GUIDE PIECE NO.

TYPE DE CHAÎNE

16” 160386001

OREGON 72L

60 28.2

20” 200387001

OREGON 72L

70 22.1

24” 240388101

OREGON 72L

81 19.2

CKA means Computed Kickback Angle.
CKA Signifie angle de rebondissement calculé.

Note; There may be other replacement

components for achieving kickback
protection. For details, please refer to
the chain and bar combination sheet
shown in the operator’s manual.

REMARQUE; Il y peut y avoir d’autres

composantes de remplacement qui
protègent en cas de rebondissement.
Pour plus de détails, se référer à la
feuille sur les combinaisons de guide et
de chaîne du manuel de l’utilisateur.

Part Number X524-000710

 CAUTION/ATTENTION

Hearing protectors meeting the requirements
of CSA Standard Z94.2 should be worn.

Les protecteurs auditifs pouvant être porter
doivent recontrer les normes CSA Standard
Z94.2.

Part Number 890176-39431

POUR ÉVITER LES REBONDISSEMENTS

1. Éviter tout contact entre le nez du

guide-chaîne et un objet quelconque.

2. Tout contact du nez peut provoquer un

mouvement brusque vers le haut ou vers
le bas et entraîner de graves blessures.

3. Toujours employer lex deux mains

pour opérer la scie à chaîne.

Part Number X505-000460

TO AVOID KICKBACK

1. Contact of the guide bar tip with any

object should be avoided.

2. Tip contact may cause the guide bar to

move suddenly upward and backward
which may cause serious injury.

3. Always use two hands when operating

the chain saw.

Part Number X505-000450

CS-670

CAUTION: For safe operation follow all
safety precautions and instructions in
operator’s Manual. (Replacement manuals
are available from your ECHO dealer.)
Hold chain saw firmly with both hands.

Part Number X503-002460

 ATTENTION

Pour un travail en sécurité, respectez toutes
les règles de sécurité et les indications du
manuel d’utilisation. (Le manuel d’utilisation
est disponibile chez votre agent ECHO.) Tenez
fermement la tronçonneuse des deux mains.

Part Number 890324-39630

* If a decal cannot be read, a new one can be

ordered from your ECHO dealer.

5

4

 7

8

10

11

12

13

14

21

16

17

18

20

3

19

15

6

22

9

23

X503-002460

X524-000710

890176-39431

890324-39630

X505-000450

X505-000460

Summary of Contents for CS-670



























Reviews:

No comments