Echo CS-670 Operator'S Manual Download Page 25

Page: 25 / 26

CS-670

TROUBLE SHOOTING

Problem

Engine

— starts hard

Cause

Remedy

— does not start

Engine

Fuel at

No fuel

•

Fuel filter clogged

•

Clean or replace

cranks

carburetor

at carburetor

•

Fuel line clogged

•

Clean

•

Carburetor

•

Ask your ECHO dealer

Fuel at

No fuel at

•

Carburetor

•

Ask your ECHO dealer

cylinder

Muffler wet

•

Fuel mixture is too rich

•

Open choke

with fuel

•

Clean/replace air filter

•

Adjust carburetor

•

Ask your ECHO dealer

Spark at

No spark at

•

Ignition switch off

•

Turn switch on

end of

end of plug

•

Electrical problem

•

Ask your ECHO dealer

plug wire

wire

•

Spark gap incorrect

•

Adjust 0.6 mm to 0.7 mm

Spark at

No spark at

•

Covered with carbon

•

Clean or replace

plug

•

Fouled with fuel

•

Clean or replace

•

Spark plug defective

•

Replace plug

Engine

•

Internal engine problem

•

Ask your ECHO dealer

does not
crank

Engine

Dies or

•

Air filter dirty

•

Clean or replace

runs

accelerates poorly

•

Fuel filter dirty

•

Clean or replace

•

Fuel vent blocked

•

Clean

•

Spark plug

•

Clean and adjust/replace

•

Carburetor

•

Adjust

•

Cooling system blocked •

Clean

•

Exhaust port/spark

•

Clean

arrestor screen blocked

↓↓↓↓↓

→

↓↓↓↓↓

→

WARNING

DANGER

FUEL VAPORS ARE EXTREMELY
FLAMMABLE AND MAY CAUSE FIRE AND/
OR EXPLOSION. NEVER TEST FOR IGNITION
SPARK BY GROUNDING SPARK PLUG NEAR
CYLINDER PLUG HOLE, OTHERWISE
SERIOUS PERSONAL INJURY MAY RESULT.

Summary of Contents for CS-670



























Search results

Summary of Contents for CS-670

Reviews:

Echo CS-670, Operator'S Manual, Page: 25 / 26

Search results

Summary of Contents for CS-670

Reviews: