background image

Page 1 of 4

Installation and Operation Instructions

ED3794 FLEXIBLE DIRECTIONAL

1

Light Head

2

Screws

1

Installation Guide

1

Mounting Gasket

1

Bezel

1

Alcohol Wipe

CONTENTS:

 Input Voltage

12-24VDC

Current

0.8A Max @ 12VDC

0.5A Max @ 24VDC

Physical H x W x L

3.9 in x 0.9 in x 0.4 in

9.9 cm x 2.3 cm x 1 cm

Ship Weight

0.1 lb (0.05 Kg)

SPECIFICATIONS:

No Pulling

Can not pull the wire because the PCB and 

components will be damaged.

No Twisting

The product can’t be twisted because the PCB and 

components will be damaged.

Maximum flex is 120 degrees

Max 30 degree

angle from 

center

Important! 

 

This unit is a safety device and it must be connected to its own 

separate, fused power point to assure its continued operation should any other 

electrical accessory fail.

Caution: 

When drilling into any vehicle surface, make sure the area is 

free from any electrical wires, fuel lines, vehicle upholstery, etc. that could be 

damaged.

Caution: 

- light cannot be twisted or pulled

- do not bend in the lens direction

- Mounts to a surface curvature with a minimum radius of 3 inches.

Do not install and/or operate this safety product unless you have read and understood the safety 

information contained in this manual.

1. 

Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices are essential to ensure the 

safety of emergency personnel and the public.

2. 

Emergency warning devices often require high electrical voltages and/or currents. Exercise caution when working with live electrical connections.

3. 

This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause high current arcing, which 

can cause personal injury and/or severe vehicle damage, including fire. 

4. 

Proper placement and installation is vital to the performance of this warning device. Install this product so that output performance of the system 

is maximized and the controls are placed within convenient reach of the operator so that they can operate the system without losing eye contact 

with the roadway.

5. 

Do not install this product or route any wires in the deployment area of an air bag.  Equipment mounted or located in an air bag deployment area 

may reduce the effectiveness of the air bag or become a projectile that could cause serious personal injury or death.  Refer to the vehicle owner’s 

manual for the air bag deployment area.  It is the responsibility of the user/operator to determine a suitable mounting location ensuring the safety 

of all passengers inside the vehicle particularly avoiding areas of potential head impact.

6. 

It is the responsibility of the vehicle operator to ensure daily that all features of this product work correctly. In use, the vehicle operator should 

ensure the projection of the warning signal is not blocked by vehicle components (i.e., open trunks or compartment doors), people, vehicles or 

other obstructions.

7. 

The use of this or any other warning device does not ensure all drivers can or will observe or react to an emergency warning signal. Never take 

the right-of-way for granted. It is the vehicle operator’s responsibility to be sure they can proceed safely before entering an intersection, drive 

against traffic, respond at a high rate of speed, or walk on or around traffic lanes.

8. 

This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obeying all laws regarding 

emergency warning devices. Therefore, the user should check all applicable city, state, and federal laws and regulations. The manufacturer 

assumes no liability for any loss resulting from the use of this warning device.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property damage, serious injury, and/or death 

to those you are seeking to protect!

Summary of Contents for ED3794














Reviews: