Eaton TRSM0020 Service Manual Download Page 71

Page: 71 / 142

Transmission appearance may differ, procedure is the same.

Shift Bar Housing

How to Remove the Shift Bar Housing

Special Instructions

Before removing the shift bar housing, the shift bar
housing cover and autoshifter must be removed.

Special Tools

Typical service mechanic tools needed

To Remove

Inspect the input and output shaft magnetic
speed sensors, remove if damaged or defective.

Inspect the ball switches, remove if defective or
damaged.

From the shift bar housing, remove the three (3)
Allen head screws.

Remove the shift bar housing.

Remove the gasket and clean all mounting
surfaces of gasket material.

If the three (3) sets of tension springs and balls
from the housing top bores are loose, tilt the
assembly and remove them.

H/47-7

H/47-9

H/11-9

H/12-6

Summary of Contents for TRSM0020















































































































































Search results

Summary of Contents for TRSM0020

Reviews:

Related manuals for TRSM0020

Brands by name

Popular brands

Eaton TRSM0020, Service Manual

Search results

Summary of Contents for TRSM0020

Reviews:

Related manuals for TRSM0020

Brands by name

Popular brands