manualshive.com logo in svg

Eaton IBC-L, Installation Manuals

The Eaton IBC-L comes with comprehensive Installation Manuals for easy and hassle-free setup. Download these user manuals for free from our website, ensuring you have all the guidance you need. Get acquainted with your Eaton IBC-L, benefiting from clear instructions and detailed illustrations—just a few clicks away at manualshive.com.

Share
Download
background image

Eaton 93PM Integrated Battery Cabinet (IBC-L, IBC-LH [432V], and IBC-LH [480V]) Installation Manual 164000228—Rev 08

vii

LLiisstt ooff TTaabblleess

Table 1.

IBC-L Cabinet Weights ................................................................................................................... 14

Table 2.

IBC-LH (432V) Cabinet Weights ........................................................................................................ 15

Table 3.

IBC-LH (480V) Cabinet Weights ........................................................................................................ 15

Table 4.

IBC-L and IBC-LH Cabinet Clearances ................................................................................................ 16

Table 5.

Line-Up-and-Match External Power Wiring Recommendations – Eaton 93PM IBC-L and 93PM IBC-LH ............ 24

Table 6.

Standalone External Power Wiring Recommendations - Eaton 93PM IBC-L................................................ 25

Table 7.

Standalone External Power Wiring Recommendations - Eaton 93PM IBC-LH ............................................. 26

Table 8.

External Power Cable Terminations – Eaton 93PM IBC-L and 93PM IBC-LH ............................................... 27

Table 9.

Recommended DC Circuit Breaker or Disconnect Ratings (Three or Four IBC-Ls or Two IBC-LHs) .................. 27

Table 10.

IBC TB2 or TB3 Interface Connections (432V) ...................................................................................... 53

Table 11.

IBC TB2 or TB3 Interface Connections (480V) ...................................................................................... 54

Table 12.

IBC TB2 or TB3 Interface Wiring Terminal Block Terminations................................................................. 56

Summary of Contents for IBC-L























































































Reviews:

No comments

Related manuals for IBC-L

TRENDnet TV-H500 - Datasheet preview
TV-H500 -
Brand: TRENDnet Pages: 2
Wharfedale Pro EVP-X15P User Manual preview
EVP-X15P
Brand: Wharfedale Pro Pages: 8
MGF MINI BOX KIT Operating & Maintenance Instruction Manual preview
MINI BOX KIT
Brand: MGF Pages: 2
Yang-IT YY-36 series Instruction Manual preview
YY-36 series
Brand: Yang-IT Pages: 4
Peavey DTH 2 Specifications preview
DTH 2
Brand: Peavey Pages: 4
Peavey DTH 118b Specifications preview
DTH 118b
Brand: Peavey Pages: 6
Peavey EUROSYS 10PM Operating Instructions Manual preview
EUROSYS 10PM
Brand: Peavey Pages: 7
Leviton LP3-MC Series Installation Instructions preview
LP3-MC Series
Brand: Leviton Pages: 2
ZALMAN Z Series II User Manual preview
Z Series II
Brand: ZALMAN Pages: 8
Repotec SMART BACKUP RP-EN252 User Manual preview
SMART BACKUP RP-EN252
Brand: Repotec Pages: 17
GAMDIAS Mars M1 Quick Installation Manual preview
Mars M1
Brand: GAMDIAS Pages: 15
Larson Electronics EPL-AED-1X-1IN-GL Instruction Manual preview
EPL-AED-1X-1IN-GL
Brand: Larson Electronics Pages: 3
StarTech.com S354UFER Instruction Manual preview
S354UFER
Brand: StarTech.com Pages: 16
D-Link ShareCenter Pulse DNS-320 Technical Specifications preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DNS-323-500GB Brochure & Specs preview
DNS-323-500GB
Brand: D-Link Pages: 2
Laser CASE-3S3 Quick Start Manual preview
CASE-3S3
Brand: Laser Pages: 2
3D Upfitters Ender 3 S1 Installation Manual preview
Ender 3 S1
Brand: 3D Upfitters Pages: 23
welland ME-700E Quick Installation Manual preview
ME-700E
Brand: welland Pages: 2

Brands by name

Popular brands

Load more brands