background image

14

Eaton 93PM Integrated Battery Cabinet (IBC-L, IBC-LH [432V], and IBC-LH [480V]) Installation Manual 164000228—Rev 08

NOTE

Emergency lighting and power equipment battery cabinets (UL924) are rated for
operation in a 20°–30°C (68°–86°F) temperature environment.

The batteries are rated for a 25°C (77°F) ambient temperature to extend their useful life.

Maximum Relative Humidity: 95%, noncondensing

CAUTION

It is recommended for optimal battery life and discharge performance to keep the ambient air temperature the
battery is used in at 25°C (77°F). Operating temperatures above the recommended range will result in
decreased battery life and performance, and will reduce or void the battery warranty. Refer to Eaton's Terms
and Conditions of Sale with Battery Replacement Coverage and the Battery Replacement Price Book for more
information. These documents can be found at

www.eaton.com/powerquality

or contact your service

representative for information on how to obtain copies.

CAUTION

The shelf life for the batteries installed in the IBC is 12 months from the date code on the battery. The recharge
date is also stated on a label inside the IBC.

Failure to recharge the batteries before the expiration of the shelf life will result in reduced discharge time,
shorter float service life, and will void the warranty.

The IBC operating environment must meet the weight requirements shown in

Table 1

,

Table 2

or

Table 3

and

the size requirements shown in

Figure 4

through

Figure 9

. Dimensions are in millimeters (inches).

Specifications are subject to change.

Table 1. IBC-L Cabinet Weights

Model

Weight kg (lb)

Shipping

Installed

Point Loading

Eaton 93PM Integrated Battery Cabinet-Large
with E54 Batteries

2189 (4827)

2144 (4727)

7 at 306 (675)

Eaton 93PM Integrated Battery Cabinet-Large
with E39 Batteries

1761 (3883)

1716 (3783)

7 at 245 (540)

Eaton 93PM Integrated Battery Cabinet-Large
with E28 Batteries

1467 (3234)

1422 (3134)

7 at 203 (448)

Eaton 93PM Integrated Battery Cabinet-Large
with E54 Batteries and sidecar

2231 (4919)

2186 (4819)

7 at 312 (688)

Eaton 93PM Integrated Battery Cabinet-Large
with E39 Batteries and sidecar

1803 (3975)

1758 (3875)

7 at 251 (554)

Eaton 93PM Integrated Battery Cabinet-Large
with E28 Batteries and sidecar

1508 (3326)

1463 (3226)

7 at 209 (461)

Installation Plan and Unpacking

Summary of Contents for IBC-L























































































Reviews: