manualshive.com logo in svg

Eaton gree motion xChargeIn DC 22, Installation Manual

Share
Download
Eaton gree motion xChargeIn DC 22 Installation Manual Download Page 45

41

 XCHARGEIN DC 22 INSTALLATION MANUAL

   MN192004EN   September 2021   www.eaton.com

00

Title

10.2  Technical datasheet

The latest version of the technical datasheet is available for download from 

www.eaton.com/xchargeindc22

.

xChargeIn DC 22 complies with the standards listed in the following table.

Certifications and standards

General

Charging mode

EN 61851-21-1, EN 61851-21-2, EN 61851-23 and EN 61851-24

Insulation

EN 60664-1

Safety

IEC 61439-1 and IEC 61439-7

Cable

Version

EN 62196-1 and EN 62196-3

Electromagnetic compatibility

Product

EN 61000-6-1 and EN 61000-6-3 

EN 61000-3-11 and EN 61000-3-12

Communication

ISO

15118

DIN

70121

CHAdeMO

0.9/1.0

Table 12.  List of standards xChargeIn DC 22 complies with

11.  Contact support information

Should any technical problems arise during the operation of the charging station, contact your Eaton technical support 

representative for assistance. The following information should be provided when contacting the Eaton technical 

support representative:

 

•

Product model and serial number

 

•

Fault messages

Summary of Contents for gree motion xChargeIn DC 22















































Reviews:

No comments

Brands by name

Popular brands

Load more brands