manualshive.com logo in svg

Eaton gree motion xChargeIn DC 22, Installation Manual

Share
Download
Eaton gree motion xChargeIn DC 22 Installation Manual Download Page 33

29

 XCHARGEIN DC 22 INSTALLATION MANUAL

   MN192004EN   September 2021   www.eaton.com

00

Title

It is possible to establish the communication via internet in two ways:

1.  LAN network: In this case the unit(s) are directly connected to a local modem/router that provides internet connection
2.  SIM card: In this case a modem/router is installed inside the unit, and a SIM card must be configured. This is an 

option.

To configure the router/modem the charging station must be powered and in standby mode.

Commissioning and configuring of the router of the charging station must be performed by qualified and 

authorized electricians who are responsible for complying with existing standards and local installation 

regulations.

WARNING - Any operation requiring the opening of the charger can lead to electric shock hazards.

Please refer to the section 8.1 of this manual to open the xChargeIn DC 22 housing.
It is possible to configure the network settings of the router located inside the EV charging station. The router is located 

inside the charging station, mounted on the DIN rail on the front cover of the enclosure as shown in the figure below.

Figure 26.  Location of the router/modem in xChargeIn DC 22

2

1

Number Description

1

Location of the router/modem

2

Ethernet cable entry

Summary of Contents for gree motion xChargeIn DC 22















































Reviews:

No comments

Brands by name

Popular brands

Load more brands