background image

 

For more information visit: 

www.EatonElectrical.com 

Initial Release 

 

Fig. A-4  MD 3001 Typical Wiring Diagram 

 
 
A5.0  DRAWOUT OPERATION 

A5.1 INSERTING THE RELAY 

Before the MD-3001 is inserted into the Drawout 
Enclosure: 

 

• 

Verify that all wiring is correct as shown in the wiring 
diagram.  

 
When inserting the MD-3001 Drawout into the Drawout 
Enclosure, use the guides to align the exterior of the 
device chassis with the interior of the enclosure. Slide the 
unit into the Case using the guides, pressing firmly until all 
four latches located on the sides of the device are seated 
and latched into place. Tabs on the MD-3001 Drawout 
Inner Chassis will prevent the inner chassis from being 
inserted upside down or being inserted into an enclosure 
of another IQ product.  

 

 

THE MD-3001 INNER CHASSIS MUST BE FULLY 
INSERTED AND FULLY LATCHED IN TO ITS 
DRAWOUT ENCLOSURE FOR PROPER 
OPERATION OF THE DEVICE.

 

 
When the unit is seated properly, the quick release buttons 
at the top and bottom of the unit will return to their non-
compressed position. The device can now be secured in 
the enclosure by inserting a utility locking ring in the 
provided slot.  

A5.2 REMOVING THE RELAY 

 

 
 

 REMOVAL OF THE MD-3001 INNER CHASSIS 
FROM THE DRAWOUT OUTER CASE EXPOSES 
LIVE PARTS, WHERE THE HAZARD OF A FATAL 

WARNING 

Summary of Contents for CUTLER-HAMMER MD-3000 series
























Reviews: