background image

Software Overview 

Options Menu 

 
 
 

 

 

COMMUNICATION SETTING: 

Opens the window to the 

right.  Allows you to choose the COM Port, Baud Rate and 
Station Address for communications to the ELC, along with 
Retries and Retry Delay settings.

 

*CHANGE ELC TYPE: 

Opens the ELC Type Setting dialog 

shown on page 10.

  

Allows you to set the type of ELC on which 

the currently open project will be used. 

AUTOSAVE SETUP: 

Opens a window that allows you to 

set software auto save features to occur either at the beginning 
of a compile function or at a specific interval (minimum is 5 
minutes).  NOTE: By default, the Auto Save box is unchecked. 

FONT SETTING AND COMMENT FORMAT: 

Opens a 

window to configure colors and fonts used in the program. 

*SET ELC DATE AND TIME: 

If an ELC is 

connected, this opens the window to the right, 
which lets you synchronize the clock in the 
ELC. 

PROMPT TO EDIT DEVICE 
COMMENT: 

When this option is checked, 

the software will automatically pop up a window 
that has a field for entering a device comment 
immediately after you enter an address by 
direct typing command in a programming 
window.   

 

 

 

 

* Available only when a project is open.

 

Pub. No. TR05003001E 

For more information visit: 

www.EatonElectrical.com

 11 

Summary of Contents for Cutler-Hammer ELC Series






















Reviews: