background image

 

Preface 

 

Information in this manual is subject to change without notice and does not 
represent a commitment on the part of Eaton Electrical Inc. Permission is granted 
to duplicate this material without modification only for your use or the internal use 
of other members of your company or your agents to assist you in the use and 
servicing of products purchased from Eaton Electrical. No permission is granted 
to modify this material or include this material in a compilation. 

Intro: 

Preface 

Support 

Services 

Exercise 2: Logic 

Instructions 

Exercise 1:  

Ladder Logic 

Connecting to 

the ELC 

Software 

Overview 

Hardware 

Overview 

Basics: 

Exercises: 

Go Chart 

Support 

Services 

Preface 

RESTRICTED RIGHTS LEGEND 

Use, duplication, or disclosure by the Government is subject to restrictions set 
forth in paragraph (b)(3)(B) of the Rights in Technical Data and Computer 
Software clause of DAR 7-104.9(a). Contractor/Manufacturer is Eaton 
Corporation, Operator Interface Business, 811 Green Crest Drive, Westerville, 
OH 43081. 

TRADEMARKS 

PanelMate, Cutler-Hammer, Eaton and ePro Canvas are either federally 
registered trademarks or trademarks of Eaton Corporation.  

Commercial brand names (trademarks) of products of manufacturers or 
developers, other than Eaton Corporation or its affiliates, that appear in this 
manual may be registered or unregistered trademarks of those respective 
manufacturers or developers, which have expressed neither approval nor 
disapproval of Cutler-Hammer

®

 products and services. 

©

2005 Eaton Electrical Inc. All rights reserved. 

Printed in the United States of America. 

P/N MN05003001E 
 
 

Navigation in This Document 

The cells to the left of the content on the even pages in this document are meant 
to show your progress through the training.  The chapter which you are currently 
viewing is highlighted.  For instance, on this page, the cells titled “Preface” and 
“Support Services” are highlighted to show what you are viewing on this page 
and the opposing page (in book format).   

Pub. No. TR05003001E 

For more information visit: 

www.EatonElectrical.com

 2 

Summary of Contents for Cutler-Hammer ELC Series






















Reviews: