Eagle CUDA 250i S/Map Installation And Operation Instructions Manual Download

Page: 120 / 172

112

Tip:

Generally, when using this method, the smaller the zoom range, the
more accurately you will be able to steer along the trail.

Navigate a Trail (forward)

The following figures illustrate the menu sequence for navigating a
trail.

1. Press

MENU

↓

RAILS

ENT

2. Press

↓

to enter the Saved Trail list, then use

↑

↓

to select the de-

sired

Trail Name

ENT

3. Press

↓

AVIGATE

ENT

4. Press

→

AVIGATE

OUTE

ENT

. The unit begins showing navigation

information along the trail.

NOTE:

If you are already located at or near the beginning of your trail, the
arrival alarm will go off as soon as you hit Enter. Just press

EXIT

clear the alarm.

5. Now, begin moving and let your Cuda 250 guide you.

6. When you reach your destination, be sure to cancel your navigation:
press

MENU

↓

ANCEL

AVIGATION

ENT

. The unit asks if you're

sure. Press

←

ENT

Summary of Contents for CUDA 250i S/Map












































































































































































Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands

Eagle CUDA 250i S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands