Eagle CUDA 250i S/Map Installation And Operation Instructions Manual Download Page 41 | Manualshive

Page: 41 / 172

background image

33

CAUTION:

Failure to use the enclosed 3-amp fuse will void your warranty! For
a replacement, use a type 3AG 3-amp fuse.

This unit has reverse polarity protection. No damage will occur if the
power wires are reversed. However, the unit will not work until the
wires are attached correctly.

Mounting the Sonar Unit: In-Dash or Bracket

You can install the sonar unit on the top of a dash with the supplied
bracket. It can also be installed in the dash with an optional FM-6
dash-mounting kit.

In-dash mounting template for Cuda 250.

NOTE: This figure is

not

printed to scale.

Top

ALWAYS VERIFY DIMENSIONS.

Cut along this line

«
...
39
40
41
42
43
...
»

Summary of Contents for CUDA 250i S/Map













































































































































































Reviews:

No comments

Related manuals for CUDA 250i S/Map

Brand: Garmin Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands