Eagle CUDA 250i S/Map Installation And Operation Instructions Manual Download Page 77

Page: 77 / 172

HyperScroll



See the entry on Ping Speed, which controls the HyperScroll feature.

Noise Rejection

See the entry on Advanced Signal Processing in this section.

Overlay Data

To change the digital data shown on top of the sonar page:

1. Press

MENU

↓

VERLAY

ATA

ENT

2. Press

↓

↑

to select

Data Type

then use

←

→

turn on the data

type and select its desired size — Small, Medium, Large or Enormous.
Data Size is displayed in the bottom of the Overlay Data Shown win-
dow and may be changed using the

←

→

keys.

Overlay Data command on the Sonar Menu (left). Overlay Data Shown

selection menu (center). In this example, we scrolled down the data list

to highlight Ground Speed. It will be displayed in a small size. Data list

with Total Distance selected (right).

After you have selected the data and the size you want, you can use

↓

↑

to select other Data Types for display.

3. To return to the previous page, press

EXIT

Summary of Contents for CUDA 250i S/Map












































































































































































Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands

Eagle CUDA 250i S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands