Eagle CUDA 250i S/Map Installation And Operation Instructions Manual Download Page 56

Page: 56 / 172

Pages

The Cuda 250 has three major Sonar display options. They are the Full
Sonar Chart, Split Zoom Sonar Chart and Digital Data.

You access display modes by pressing the

PAGES

key. Press

→

ONAR

↑

↓

desired page

ENT

. Press

EXIT

to clear the Page menu.

The Full Sonar Chart is the main Sonar display option. This is a cross-
section view of the water column beneath the boat. The chart moves
across the screen, displaying sonar signals that represent fish, struc-
ture and the bottom.

Sonar Page, showing full sonar chart mode.

Surface clutter

Structure

Bottom signal

Fish arches
around
school of
bait fish

In FasTrack, fish
arches show as
horizontal bars.

Depth scale

Digital data
overlay
(depth &
temperature)

Surface signal

Zoom bar

FasTrack

bar graph

Summary of Contents for CUDA 250i S/Map












































































































































































Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands

Eagle CUDA 250i S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands