Eagle CUDA 250i S/Map Installation And Operation Instructions Manual Download

Page: 164 / 172

156

Press

↑

↓

to change the first character, then press

→

to the next char-

acter and repeat until the entry is correct, the press

EXIT

Trail Options menu with Update Rate setting (left)

and Update Distance setting (right).

Specific Trail Options

Delete Trail

To delete a specific trail: From the Trails Menu, press

↓

Trail

Name

ENT

. The Edit Trail menu appears as seen in the following fig-

ure. Press

↓

ELETE

RAIL

ENT

←

ENT

Edit Trail menu (left) with Delete Trail highlighted. Delete Trail con-

firmation message (center). New Trail selected on Trails menu (right).

Summary of Contents for CUDA 250i S/Map












































































































































































Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands

Eagle CUDA 250i S/Map, Installation And Operation Instructions Manual

Search results

Summary of Contents for CUDA 250i S/Map

Reviews:

Related manuals for CUDA 250i S/Map

Brands by name

Popular brands