E-FLITE Blade CP Pro Instruction Manual Download Page 9 | Manualshive

Page: 9 / 64

background image

9

It is important that you only charge the included 11.1V 800mAh -cell Li-Po Battery Pack (EFLB099)
with the included -cell 11.1V Li-Po Balance Charger (EFLC10). Your battery pack is equipped with
special Charge Protection Circuitry and a Balance Charge Lead with connector that is only compatible
with this charger. Attempting to charge the pack using another Li-Po charger or non Li-Po compatible
charger could result in serious damage. Please familiarize yourself thoroughly with the warnings and
guidelines (pages –8) before continuing.

The.included.3-cell.11 .1V.Li-Po.Balance.Charger.will.charge.a.near.fully.discharged.(not.over-discharged)..
11 .1V.800mAh.3-cell.Li-Po.Battery.Pack.in.approximately.1 .0–1 .5.hours ..In.some.cases.the.charge.time..
may.be.shorter.depending.on.the.actual.amount.of.capacity.left.in.the.pack.after.a.flight ..NEVER charge the
battery unattended.

Note:.The.Li-Po.battery.pack.included.with.your.Blade™.CP.Pro.will.arrive.partially.charged ..For.this.reason.the.

initial.charge.may.only.take.approximately.30–50.minutes .

The.charger.requires.up.to.1 .5.Amps.of.11 .5–15.Volt.DC.input.power.that.can.be.supplied.from.a.small.12V.gel.
cell.or.car.battery .

«
...
7
8
9
10
11
...
»

Summary of Contents for Blade CP Pro

































































Reviews:

No comments

Related manuals for Blade CP Pro

Operating Lighthouse

Brand: Lionel Pages: 8

Brand: HobbyBoss Pages: 8

Brand: LCUT Creative Pages: 2

Poterie Professional POTTERY Studio

Brand: Buki Pages: 32

Brand: Old School Model Works Pages: 20

E 50/BR 150 22154

Brand: Trix Pages: 40

Cathy II P-51 Mustang

Brand: AIR core Pages: 2

Brand: Eduard Pages: 4

Brand: Little Tikes Pages: 2

CHOU CHOU Magic Pacifier

Brand: Zapf Creation Pages: 5

Brand: Horizon Hobby Pages: 18

Brand: Fisher-Price Pages: 28

Focke-Wulf 190 D9

Brand: Top Flite Pages: 65

V.Flash: Scooby-Doo Ancient Adventure

Brand: VTech Pages: 20

Radio Control Pterodactyl

Brand: Toysrus Pages: 2

Ultra Micro DH 98 Mosquito Mk VI

Brand: PARKZONE Pages: 64

P-51D Mustang 40

Brand: Kyosho Pages: 18

Brand: Step2 Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands