E-FLITE Blade CP Pro Instruction Manual Download Page 6

Page: 6 / 64

Safety, Precautions, and Warnings

As.the.user.of.this.product.you.are.solely.responsible.for.operating.it.in.manner.that.does.not.endanger.yourself.

and.others.or.result.in.damage.to.the.product.or.the.property.of.others .
This.model.is.controlled.by.a.radio.signal.that.is.subject.to.interference.from.many.sources.outside.your.control ..

This.interference.can.cause.momentary.loss.of.control.so.it.is.advisable.to.always.keep.a.safe.distance.in.all.

directions.around.your.model,.as.this.margin.will.help.to.avoid.collisions.or.injury .
•. Never.operate.your.model.with.low.transmitter.batteries .

•. Always.operate.your.model.in.an.open.area.away.from.cars,.traffic,.or.people .

•. Avoid.operating.your.model.in.the.street.where.injury.or.damage.can.occur .

•. Never.operate.the.model.out.into.the.street.or.populated.areas.for.any.reason .

•. Carefully.follow.the.directions.and.warnings.for.this.and.any.optional.support.equipment.(chargers,.rechargeable.

battery.packs,.etc .).that.you.use .

•. Keep.all.chemicals,.small.parts.and.anything.electrical.out.of.the.reach.of.children .

•. Moisture.causes.damage.to.electronics ..Avoid.water.exposure.to.all.equipment.not.specifically.designed.and.

protected.for.this.purpose .

•. Never.lick.or.place.any.portion.of.your.Blade™.CP.Pro.in.your.mouth.as.it.could.cause.serious.injury..

or.even.death .

Additional Required Equipment

No.additional.equipment.is.required.to.complete.your.Blade.CP.Pro .

Blade CP Pro RTF Contents

Item

Description

Not Available Separately Blade CP Pro RTF Airframe

EFLH1046

6CH CCPM Pro Transmitter FM 72MHz

EFLB0995

11.1V 800mAh 3-Cell Li-Po, JST/Balance

EFLC3105

3-Cell Li-Po Balance Charger, 0.8A

EFLH1129

Mounting Accessories & Wrench

Not Available Separately Hook and Loop Material

Summary of Contents for Blade CP Pro

































































Search results

Summary of Contents for Blade CP Pro

Reviews:

Related manuals for Blade CP Pro

Brands by name

Popular brands

E-FLITE Blade CP Pro, Instruction Manual

Search results

Summary of Contents for Blade CP Pro

Reviews:

Related manuals for Blade CP Pro

Brands by name

Popular brands