manualshive.com logo in svg

E-FLITE Blade CP Pro, Instruction Manual

Share
Download
E-FLITE Blade CP Pro Instruction Manual Download Page 26

When.the.“Idle.Up”.switch.is.toggled.toward.the.rear.of.the.transmitter,.the.Blade™.CP.Pro.will.be.flying.in.“Normal.
Mode .”.In.this.flight.mode,.the.throttle.curve.is.linear.from.0%.to.100%,.with.a.pitch.range.of.approximately.-1.
degree.to.+12.degrees ..(See.page.31.for.additional.data.and.graphics.relating.to.the.throttle.and.pitch.curves.
preset.for.your.Blade.CP.Pro .).This.is.the.preferred.flight.mode.for.general.hovering.and.gentle.forward.flight .

When.the.“Idle.Up”.switch.is.toggled.toward.the.front.of.the.transmitter,.the.Blade.CP.Pro.will.be.flying.in.the.
“Stunt.(aerobatic)”.flight.mode ..In.this.flight.mode,.the.throttle.curve.will.be.“V”.or.“Flat-Line”.shaped.from.100%.to.
100%.with.approximately.50%.to.100%.throttle.at.mid-stick.(the.mid-stick.throttle.percentage.value.will.depend.on.
where.the.“Idle.Up.Throttle.Curve.Midpoint.Adjustment”.knob.is.set,.as.outlined.on.pages.27–29) ..The.pitch.range.
will.then.be.approximately.-12.to.+12.degrees.(See.pages.31–32.for.additional.data.and.graphics.relating.to.the.
throttle.and.pitch.curves.pre-set.for.your.Blade.CP.Pro) ..This.flight.mode.is.preferred.for.aggressive.forward.flight.
and.aerobatics,.as.well.as.inverted.flying .

Note: When in the Idle Up/Stunt flight mode, even with the throttle stick all the way down, the blades 

and motors will continue to spin. You must use the Normal flight mode to safely turn off the motors. 

For safety, the -in-1 unit will not arm if the flight battery is plugged in and the flight mode switch is in 

the Idle Up/Stunt position.

When.switching.between.Normal.and.Idle.Up/Stunt.flight.modes,.it.is.best.to.do.so.in.the.air.while.hovering ..The.
throttle.and.pitch.curves.of.each.flight.mode.have.been.optimized.to.transition.smoothly.around.hover ..Please.be.
sure.to.never.switch.into.the.Idle.Up/Stunt.mode.without.having.powered.the.main.and.tail.motors.up.in.Normal.
mode.first ..The.abrupt.start.could.cause.damage.to.the.gears,.motors.or.possibly.even.the.3-in-1.unit .

Summary of Contents for Blade CP Pro

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands