manualshive.com logo in svg

E-FLITE Blade CP Pro, Instruction Manual

The E-FLITE Blade CP Pro is a high-performance helicopter designed for skilled pilots. To fully master its capabilities, ensure you have the comprehensive Instruction Manual. Download it for free from manualshive.com and delve into the detailed manual to maximize your experience with this remarkable helicopter.

Share
Download
background image

Limited Warranty & Limits of Liability

Pursuant.to.this.Limited.Warranty,.Horizon.Hobby,.Inc ..will,.at.its.option,.(i).repair.or.(ii).replace,.any.product.
determined.by.Horizon.Hobby,.Inc ..to.be.defective ..In.the.event.of.a.defect,.these.are.your.exclusive.remedies .

This.warranty.does.not.cover.cosmetic.damage.or.damage.due.to.acts.of.God,.accident,.misuse,.abuse,.
negligence,.commercial.use,.or.modification.of.or.to.any.part.of.the.product ..This.warranty.does.not.cover.
damage.due.to.improper.installation,.operation,.maintenance,.or.attempted.repair.by.anyone.other.than.an.
authorized.Horizon.Hobby,.Inc ..service.center ..This.warranty.is.limited.to.the.original.purchaser.and.is.not.
transferable ..In.no.case.shall.Horizon.Hobby’s.liability.exceed.the.original.cost.of.the.purchased.product.and.will.
not.cover.consequential,.incidental.or.collateral.damage ..Horizon.Hobby,.Inc ..reserves.the.right.to.inspect.any.and.
all.equipment.involved.in.a.warranty.claim ..Repair.or.replacement.decisions.are.at.the.sole.discretion.of.Horizon.

Hobby,.Inc ..Further,.Horizon.Hobby.reserves.the.right.to.change.or.modify.this.warranty.without.notice .

REPAIR.OR.REPLACEMENT.AS.PROVIDED.UNDER.THIS.WARRANTY.IS.THE.EXCLUSIVE.REMEDY.OF.THE.
CONSUMER ..HORIZON.HOBBY,.INC ..SHALL.NOT.BE.LIABLE.FOR.ANY.INCIDENTAL.OR.CONSEQUENTIAL.DAMAGES .

As.Horizon.Hobby,.Inc ..has.no.control.over.use,.setup,.final.assembly,.modification.or.misuse,.no.liability.shall.be.
assumed.nor.accepted.for.any.resulting.damage.or.injury ..By.the.act.of.use,.setup.or.assembly,.the.user.accepts.
all.resulting.liability .

If.you.as.the.purchaser.or.user.are.not.prepared.to.accept.the.liability.associated.with.the.use.of.this.product,.you.
are.advised.to.return.this.product.immediately.in.new.and.unused.condition.to.the.place.of.purchase .

Safety Precautions

This.is.a.sophisticated.hobby.product.and.not.a.toy ..It.must.be.operated.with.caution.and.common.sense.and.
requires.some.basic.mechanical.ability ..Failure.to.operate.this.product.in.a.safe.and.responsible.manner.could.
result.in.injury.or.damage.to.the.product.or.other.property ..This.product.is.not.intended.for.use.by.children.without.
direct.adult.supervision .

The.product.manual.contains.instructions.for.safety,.operation.and.maintenance ..It.is.essential.to.read.and.follow.
all.the.instructions.and.warnings.in.the.manual,.prior.to.assembly,.setup.or.use,.in.order.to.operate.correctly.and.
avoid.damage.or.injury .

Questions, Assistance, and Repairs

Your.local.hobby.store.and/or.place.of.purchase.cannot.provide.warranty.support.or.repair ..Once.assembly,.setup.
or.use.of.the.product.has.been.started,.you.must.contact.Horizon.Hobby,.Inc ..directly ..This.will.enable.Horizon.to.
better.answer.your.questions.and.service.you.in.the.event.that.you.may.need.any.assistance .

Questions or Assistance

For.questions.or.assistance,.please.direct.your.email.to.productsupport@horizonhobby .com,.or.call..
1-877-504-0233.toll.free.to.speak.to.a.service.technician .

Summary of Contents for Blade CP Pro

































































Reviews:

No comments

Related manuals for Blade CP Pro

Lionel 2544W Santa Fe Owner'S Manual preview
2544W Santa Fe
Brand: Lionel Pages: 28
Blade 500 3D Instruction Manual preview
500 3D
Brand: Blade Pages: 17
Accucraft trains D&RGW K37 2-8-2 Instruction Manual preview
D&RGW K37 2-8-2
Brand: Accucraft trains Pages: 6
Idena 617.1229 Instructions preview
617.1229
Brand: Idena Pages: 3
K'Nex Education 79318 Manual preview
Education 79318
Brand: K'Nex Pages: 6
Fisher-Price Creative Genius Owner'S Manual preview
Creative Genius
Brand: Fisher-Price Pages: 56
Phoenix Model Cariba Mk2 Quick Start Manual preview
Cariba Mk2
Brand: Phoenix Model Pages: 3
Badger Basket LONDON DOLL PRAM Assembly And Use Instructions preview
LONDON DOLL PRAM
Brand: Badger Basket Pages: 4
Hasbro Spiderman 3 Unleashed 360 Web Spiderman 69168/69113 Instruction Manual preview
Spiderman 3 Unleashed 360 Web Spiderman 69168/69113
Brand: Hasbro Pages: 1
Beyblade Metal Draciel Instructions preview
Metal Draciel
Brand: Beyblade Pages: 2
Multiplex FunJET Ultra Building Instructions preview
FunJET Ultra
Brand: Multiplex Pages: 32
Jamara Kids 460403 Instructions Manual preview
460403
Brand: Jamara Kids Pages: 12
Hangar 9 Clipped Wing Taylorcraft ARF Installation Manual preview
Clipped Wing Taylorcraft ARF
Brand: Hangar 9 Pages: 16
marklin BR 120 Manual preview
BR 120
Brand: marklin Pages: 12
Tamiya Volkswagen Beetle Instruction Manual preview
Volkswagen Beetle
Brand: Tamiya Pages: 24
Tamiya 14079 Manual preview
14079
Brand: Tamiya Pages: 10
Tamiya 36210 Manual preview
36210
Brand: Tamiya Pages: 20
UAV Model Skywalker X8 Installation Manual preview
Skywalker X8
Brand: UAV Model Pages: 31

Brands by name

Popular brands

Load more brands