manualshive.com logo in svg

E-FLITE Blade CP Pro, Instruction Manual

Share
Download
E-FLITE Blade CP Pro Instruction Manual Download Page 27

Idle Up Throttle Curve Midpoint Adjustment Knob Description and Adjustment

The.transmitter.included.with.your.Blade™.CP.Pro.is.equipped.with.an.“Idle.Up.Throttle.Curve.Midpoint.Adjustment”.
knob.(labeled.as.“Idle.Up.TCM.ADJ”).on.the.top.left.panel,.just.ahead.of.the.“Trainer”.switch ..

This.knob.allows.you.to.adjust.the.midpoint.value.of.the.throttle.curve.when.in.the.Idle.Up/Stunt.flight.mode,.from.
approximately.50%.power.to.100%.power ..It.has.no.affect.on.the.throttle.curve.in.the.Normal.flight.mode,.or.on.
the.endpoints.of.the.throttle.curve.in.the.Idle.Up/Stunt.flight.mode .

When.the.knob.is.in.the.lowest,.most.counterclockwise.position.(-),.the.midpoint.of.the.throttle.curve.in.the.Idle.Up/
Stunt.flight.mode.will.be.approximately.50% .

When.the.knob.is.in.the.middle.position,.pointing.directly.toward.the.back.of.the.transmitter,.the.midpoint.of.the.
throttle.curve.in.the.Idle.Up/Stunt.flight.mode.will.be.approximately.75% .

Summary of Contents for Blade CP Pro

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands