E-FLITE Beechcraft Bonanza 15e ARF Assembly Manual Download Page 50

Page: 50 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Final Assembly

Parts Required

Fuselage

Wing

Wing bolts (2)

3-inch Y-harnesses (3)

Radio

9-inch servo extension

2mm x 5mm machine screw

Tools Required

Felt-tipped pen

#1 Phillips screwdriver

Dental floss

Low-tack tape

3/16-inch flat blade screwdriver

□

Step 1

Use a 3/16-inch straight blade screwdriver to install

the wing on the fuselage. Make sure that no servo

leads are trapped between the wing and fuselage.

□

Step 2

Connect a 3-inch Y-harness to the rudder and

nosewheel steering servos.

□

Step 3

Plug the Y-harness into the rudder channel of the

receiver.

□

Step 4

Plug the elevator servo lead into the receiver.

□

Step 5

Use low-tack tape and a felt-tipped pen to label the

female plugs of a 3-inch Y-harness and plug it into

the flap channel of the receiver (Aux 1). Plug the flap

servo leads from the wing into the Y-harness.

Note:

Because both flap servos have the same

direction of rotation the flap servo leads can be

connected to either plug of the Y-harness.

□

Step 6

Label a 3-inch Y-harness and plug it into the aileron

channel of the receiver. Plug the aileron servo leads

from the wing into the Y-harness.

Summary of Contents for Beechcraft Bonanza 15e ARF





























































Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands

E-FLITE Beechcraft Bonanza 15e ARF, Assembly Manual

Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands