E-FLITE Beechcraft Bonanza 15e ARF Assembly Manual Download Page 31

Page: 31 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□□

Step 2

Mark the mounting hole locations with a pencil.

□□

Step 3

Use a 5/64-inch drill bit in a pin vise to drill the holes.

□□

Step 4

Apply a drop of thin CA to each hole to strengthen

the wood. Allow the CA to cure completely without

using accelerator.

□□

Step 5

Use a #1 Phillips screwdriver to install the landing

gear with four #4 x 7/16-inch countersunk wood

screws.

Optional Retract Installation

Nose Gear

Parts Required

Fuselage

Retractable nose gear

2-inch nosewheel

Adjustable axle

#4 x 7/16-inch countersunk wood screws (4)

Tools Required

Ruler

Felt-tipped pen

File

#1 Phillips screwdriver

1.5mm hex wrench 2.5mm hex wrench

Threadlock

Hobby knife

Pin vise

5/64-inch drill bit

Low-tack tape

Pliers

Razor saw

Thin CA

Rotary tool with cutoff wheel

□

Step 1

Use a ruler to measure 4 13/16 inches from the

mounting surface of the retractable nose gear and

make a mark on the gear leg with a felt-tipped pen.

Summary of Contents for Beechcraft Bonanza 15e ARF





























































Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands

E-FLITE Beechcraft Bonanza 15e ARF, Assembly Manual

Search results

Summary of Contents for Beechcraft Bonanza 15e ARF

Reviews:

Related manuals for Beechcraft Bonanza 15e ARF

Brands by name

Popular brands